1 通过 yum 安装依赖的库以及环境
yum install rrdtool wqy* fping curl bind-utils httpd httpd-devel \ perl perl-FCGI perl-CGI perl-CGI-SpeedyCGI perl-libwww-perl perl-Socket6 perl-Net-Telnet perl-Net-OpenSSH perl-Net-DNS perl-LDAP perl-IO-Socket-SSL perl-ExtUtils-MakeMaker rrdtool-perl perl-Sys-Syslog
2 编译安装 smokeping
cd /usr/local/src/
wget http://oss.oetiker.ch/smokeping/pub/smokeping-2.6.11.tar.gz
tar xvf smokeping-2.6..tar.gz
cd smokeping-2.6.
./setup/build-perl-modules.sh /usr/local/smokeping/thirdparty
./configure --prefix=/usr/local/smokeping
gmake install
3 配置 smokeping 相关文件目录
cd /usr/local/smokeping/
mkdir cache data var
touch /var/log/smokeping.log
chown apache.apache cache/ data/ var/ /var/log/smokeping.log
cd /usr/local/smokeping/htdocs/
cp smokeping.fcgi.dist smokeping.fcgi
cp /usr/local/smokeping/etc/config.dist /usr/local/smokeping/etc/config
vim /usr/local/smokeping/etc/config # 修改 /usr/local/smokeping/etc/config 文件 # 修改 cgiurl
sed -i 's#some.url#192.168.56.11#' /usr/local/smokeping/etc/config # 默认检测时间 秒修改 秒
sed -i 's#300#60#g' /usr/local/smokeping/etc/config # 默认 秒 ping 次，修改为 秒 ping 次
sed -i 's#pings = 20#pings = 60#' /usr/local/smokeping/etc/config # 在 presentation 后添加 utf- 中文字符集
vim /usr/local/smokeping/etc/config *** Presentation *** charset = utf- # 修改密码文件权限
chmod /usr/local/smokeping/etc/smokeping_secrets.dist
4 配置 apache
4.1 设置登录密码认证
htpasswd -c /usr/local/smokeping/htdocs/htpasswd jamin
4.2 修改 apache 配置文件，配置 smokeping 站点目录
vim /etc/httpd/conf/httpd.conf
DocumentRoot "/var/www/html" 下添加如下内容 Alias /cache "/usr/local/smokeping/cache/"
Alias /cropper "/usr/local/smokeping/htdocs/cropper/"
Alias /smokeping "/usr/local/smokeping/htdocs/smokeping.fcgi" <Directory "/usr/local/smokeping">
AllowOverride None
Options All
AddHandler cgi-script .fcgi .cgi
Order allow,deny
Allow from all
AuthName "Smokeping"
AuthType Basic
AuthUserFile /usr/local/smokeping/htdocs/htpasswd
Require valid-user
DirectoryIndex smokeping.fcgi
</Directory>
5 启动服务以及访问 smokeping
systemctl start httpd
/usr/local/smokeping/bin/smokeping
访问 URL:
http://服务器ip/smokeping
6 smokeping 使用
6.1 添加需要监控的节点
注意事项：
1 在 /usr/local/smokeping/etc/config 中添加
2 smokeping 就这点不好，添加节点不能在前台 Web 页面添加，一定要在后台的配置文件中添加
3 修改 /usr/local/smokeping/etc/config 后，必须重启 smokeping 程序，配置才会生效
4 smokeping 会根据配置文件 config 在 /usr/local/smokeping/data 之下添加文件夹及子文件夹
5 用 VMware Workstation 的虚拟机测试有一点好处，虚拟网卡可以设置出入的丢包率，适合 smokeping 做丢包测试，经过测试 smokeping 检测出的丢包率与 VMware Workstation 虚拟网卡设置的丢包率基本相同，也就是说 smokeping 能够反应网络的真实状况
添加监控节点示例：注意 + 是第一层，++ 是第二层，+++ 是第三层
以下附上一份三大运营商网络监控样例配置（在 /usr/local/smokeping/etc/config 最后添加）：
+ Other
menu = 三大网络监控
title = 监控统计 ++ CT menu = 电信网络监控
title = 电信网络监控列表
host = /Other/CT/CT-BJ /Other/CT/CT-TJ /Other/CT/CT-HLJ /Other/CT/CT-SH /Other/CT/CT-SC /Other/CT/CT-GZ +++ CT-BJ menu = 北京电信
title = 北京电信
alerts = someloss
host = 202.96.199.133 +++ CT-TJ menu = 天津电信
title = 天津电信
alerts = someloss
host = 219.150.32.132 +++ CT-HLJ menu = 黑龙江电信
title = 黑龙江电信
alerts = someloss
host = 219.147.198.242 +++ CT-SH menu = 上海电信
title = 上海电信
alerts = someloss
host = 116.228.111.118 +++ CT-SC menu = 四川电信
title = 四川电信
alerts = someloss
host = 61.139.2.69 +++ CT-GZ menu = 广东电信
title = 广东电信
alerts = someloss
host = 113.111.211.22 ++ CU menu = 联通网络监控
title = 联通网络监控列表
host = /Other/CU/CU-BJ /Other/CU/CU-TJ /Other/CU/CU-HLJ /Other/CU/CU-SH /Other/CU/CU-SC /Other/CU/CU-GZ +++ CU-BJ menu = 北京联通
title = 北京联通
alerts = someloss
host = 61.135.169.121 +++ CU-TJ menu = 天津联通
title = 天津联通
alerts = someloss
host = 202.99.96.68 +++ CU-HLJ menu = 黑龙江联通
title = 黑龙江联通
alerts = someloss
host = 202.97.224.69 +++ CU-SH menu = 上海联通
title = 上海联通
alerts = someloss
host = 210.22.84.3 +++ CU-SC menu = 四川联通
title = 四川联通
alerts = someloss
host = 119.6.6.6 +++ CU-GZ menu = 广东联通
title = 广东联通
alerts = someloss
host = 221.5.88.88 ++ CMCC menu = 移动网络监控
title = 移动网络监控列表
host = /Other/CMCC/CMCC-BJ /Other/CMCC/CMCC-TJ /Other/CMCC/CMCC-HLJ /Other/CMCC/CMCC-SH /Other/CMCC/CMCC-SC /Other/CMCC/CMCC-GZ +++ CMCC-BJ menu = 北京移动
title = 北京移动
alerts = someloss
host = 221.130.33.52 +++ CMCC-TJ menu = 天津移动
title = 天津移动
alerts = someloss
host = 211.137.160.5 +++ CMCC-HLJ menu = 黑龙江移动
title = 黑龙江移动
alerts = someloss
host = 211.137.241.35 +++ CMCC-SH menu = 上海移动
title = 上海移动
alerts = someloss
host = 117.131.19.23 +++ CMCC-SC menu = 四川移动
title = 四川移动
alerts = someloss
host = 218.201.4.3 +++ CMCC-GZ menu = 广东移动
title = 广东移动
alerts = someloss
host = 211.136.192.6
参考文章：http://jaminzhang.github.io/monitoring/smokeping-deploy-practice/#top4
报错
1 .fping yum安装没有正常安装上去，需手动下载fping安装包，源码安装，在配置文件中修改fping命令的路径
2. 安装./setup/build-perl-modules.sh /usr/local/smokeping/thirdparty 时安装不上，可从另外能成功安装的一台上tar 打包文件夹thirdparty, 再传到这台解压缩到相应目录。
遇到部分IP不能直接进行ping操作，可用tcping命令结合smokeping , 必须在Centos 6 上部署。
先安装 tcping 命令
To install tcptraceroute on CentOS/REHL, first set up RepoForge on your system, and then:
$ sudo yum install tcptraceroute
Finally, download tcpping from the web.
$ cd /usr/bin
$ sudo wget http://www.vdberg.org/~richard/tcpping
$ sudo chmod tcpping
To measure network latency by using tcpping, simply run it as follows.
$ tcpping www.cnn.com
seq : tcp response from 157.166.240.13 [open] 82.544 ms
seq : tcp response from 157.166.241.10 [open] 80.771 ms
seq : tcp response from 157.166.241.11 [open] 80.838 ms
seq : tcp response from 157.166.241.10 [open] 80.145 ms
seq : tcp response from 157.166.240.11 [open] 86.253 ms
tcping 结合smokeping 配置文件示例：
*** General *** owner = Peter Random
contact = some@address.nowhere
mailhost = my.mail.host
sendmail = /usr/sbin/sendmail
# NOTE: do not put the Image Cache below cgi-bin
# since all files under cgi-bin will be executed ... this is not
# good for images.
imgcache = /usr/local/smokeping/cache
imgurl = cache
datadir = /usr/local/smokeping/data
piddir = /usr/local/smokeping/var
cgiurl = http://192.168.56.11/smokeping.cgi
smokemail = /usr/local/smokeping/etc/smokemail.dist
tmail = /usr/local/smokeping/etc/tmail.dist
# specify this to get syslog logging
syslogfacility = local0
# each probe is now run in its own process
# disable this to revert to the old behaviour
# concurrentprobes = no *** Alerts ***
to = alertee@address.somewhere
from = smokealert@company.xy +someloss
type = loss
# in percent
pattern = >%,**,>%,**,>%
comment = loss times in a row *** Database *** step =
pings = # consfn mrhb steps total AVERAGE 0.5
AVERAGE 0.5
MIN 0.5
MAX 0.5
AVERAGE 0.5
MAX 0.5
MIN 0.5 *** Presentation ***
charset = utf-
template = /usr/local/smokeping/etc/basepage.html.dist + charts menu = Charts
title = The most interesting destinations ++ stddev
sorter = StdDev(entries=>)
title = Top Standard Deviation
menu = Std Deviation
format = Standard Deviation %f ++ max
sorter = Max(entries=>)
title = Top Max Roundtrip Time
menu = by Max
format = Max Roundtrip Time %f seconds ++ loss
sorter = Loss(entries=>)
title = Top Packet Loss
menu = Loss
format = Packets Lost %f ++ median
sorter = Median(entries=>)
title = Top Median Roundtrip Time
menu = by Median
format = Median RTT %f seconds + overview width =
height =
range = 10h + detail width =
height =
unison_tolerance = "Last 3 Hours" 3h
"Last 30 Hours" 30h
"Last 10 Days" 10d
"Last 400 Days" 400d #+ hierarchies
#++ owner
#title = Host Owner
#++ location
#title = Location *** Probes *** + TCPPing binary = /usr/bin/tcpping
forks =
offset = %
step =
#tcptraceroute = -e "sudo /usr/bin/tcptraceroute"
timeout = *** Slaves ***
secrets=/usr/local/smokeping/etc/smokeping_secrets.dist
+boomer
display_name=boomer
color=0000ff +slave2
display_name=another
color=00ff00 *** Targets *** probe = TCPPing menu = Top
title = Network Latency Grapher
remark = Welcome to the SmokePing website of xxx Company. \
Here you will learn all about the latency of our network. + mytarget menu = TestTCP
title = TestTCP
host = 82.223.245.88
pings =
port =
参考文章：https://oss.oetiker.ch/smokeping/probe/TCPPing.en.html
http://blog.xuite.net/pt.hsu/life/59708395-Smokeping%E4%B9%8BTCPPing%E6%A8%A1%E7%B5%84%E7%AF%87.