DFI LP DK P45 T2RS PLUS BIOS SETTING

时间:2023-03-25 15:27:08
standard cmos features

date (mm:dd:yy) mon,oct 11 2016
time (hh:mm:ss) 10 : 10 : 26

ide channel 0 sandisk sdssdhp128g
ide channel 0 tsstcorp cddvdw sh-2
ide channel 1 none
ide channel 1 none
drive a none
video ega/vga
halt on all errors
base memory 639k
extended memory 8386560k
total memory 8387584k

advanced bios features

hard disk boot priority press enter
virus warning disabled
cpu l3 cache enable
quick power on self test enable
first boot device floppy
third boot device hard disk
second boot device cdrom
boot other device enable
boot up floppy seek enabled
boot up numlock status on
gate a20 option fast
typematic rate setting disabled
typematic rate (chars/sec) 6
typematic delay (msec) 250
security option setup
apic mode enabled
mps version control for os 1.4
os select for dram > 64mb non-os2
report no fdd for win 95 no
full screen logo show enabled

advanced chipset features

system bios cacheable enabled
memory hole at 15m-16m disabled
pci express root port func press enter
pci-e compliancy mode v1.0a

genie bios setting

cpu feature press enter
dram timing press enter
voltage setting press enter
exit setup shutdown mode 2
shutdown after ac loss disabled
ac shutdown free disabled
o.c. fail retry counter 1
o.c. fail cmos reload disabled
cpu clock ratio 9 x
cpu n/2 ratio disabled
target cpu clock 3600 mhz
cpu clock 400 mhz
boot up clock auto
cpu clock amplitude 1000mv
cpu clock0 skew 0ps
cpu clock1 skew 0ps
dram speed 400/800
target dram speed ddr2 800
pcie clock 100 mhz
cpu spread specturm disabled
pcie spread spectrum disabled

cpu feature

thermal management control:disable
ppm(eist) mode:disable
limit cpuid maxval:disable
c1e function:disable
execute disable bit:enable
virtualization technology:enable
core multi-processing:enable

dram timing

enhance data transmitting:auto
enhance addressing:auto
t2 dispatch:auto
clock setting fine delay press enter
flex memory mode:auto
cas latency time (tcl):auto
ras# to cas# delay (trcd):auto
ras# precharge (trp):auto
precharge delay (tras):auto
all precharge to act:auto
ref to act delay (trfc):auto
performance lvl(read delay):auto
read delay phase adjust:press to enter
write to pre delay(twr):auto
rank write to read(twrt):auto
act to act delay(trrd):auto
read to write delay(trdwr):auto
ranks write to write(twrwr):auto
ranks write to read(twrrd):auto
read cas# precharge(trtp):auto
all pre to refresh:auto

voltage setting

cpu vid special add:+100mv
dram voltage control:2.100v
sb core/cpu pll voltage:1.55v
nb core voltage:1.2700v
cpu vtt voltage:1.24v
vcore droop control:enable
clockgen voltage control:3.85v
cpu gtl 0/2 ref volt:0.67x
cpu gtl 1/3 ref volt:0.67x
north bridge gtl ref volt:0.67x
fsb vref:00

integrated peripherals

onchip ide device press enter
onboard device press enter
superio device press enter
usb device setting press enter

onchip ide device

sata mode ahci
legacy mode support disabled
onboard jmb363 disabled

onboard device

onboard lan enabled
onboard hd audio disabled
onboard lan pxe disabled

super io device

power on by mouse disabled
power on by keyboard disabled
power on by button enabled
kb power on password enter
hot key power on ctrl-f1
onboard fdc controller disabled
onboard serial port 1 disabled
onboard serial port 2 disabled
uart mode select irda
pwron after pwr-fail off
cir port address disabled
cir port irq 11

usb device setting

usb 1.0 controller enabled
usb 2.0 controller enabled
usb operation mode high speed
usb keyboard function enabled
usb mouse function enabled
usb storage function enabled
usb mass storage device boot setting