Arduino+sim800C家居安防火灾报警 拨打电话 发送短信例程程序

家居安防报警器，参考程序。

火灾报警

涉及用sim800c发短信,拨打电话通知。

接线：

Sim800c 3.3V -> Arduino 3.3V
Sim800c GND -> Arduino GND
Sim800c RX -> Arduino TX
Sim800c TX -> Arduino RX

#include <SoftwareSerial.h>        // 采用软件的串口
#define Infrared 7     //启动开关

SoftwareSerial SIM800C(10, 11);     // Serial RX, TX
boolean bState, bOldState;
int incomingByte = 0;               // for incoming serial data
int Infrared_NUM = 0;

void setup() {
  // put your setup code here, to run once:
  // Open serial communications and wait for port to open
  pinMode(13, OUTPUT);
  pinMode(12, OUTPUT);
  pinMode(Infrared,INPUT_PULLUP);
  digitalWrite(13,LOW);
  digitalWrite(12,LOW);

  Serial.begin(9600);
  while (!Serial) {  // wait for serial port to connect. Needed for native USB port only
  } 

  Serial.println("Good Morning, my old friend!");

  SIM800C.begin(9600);
  SIM800C.println("AT+CMGF=1");

}

void loop() {
  // put your main code here, to run repeatedly:
  if (SIM800C.available()) {
    Serial.write(SIM800C.read());
    digitalWrite(13, HIGH);// 如果通信成功，则把Arduino上面的L13 LED 灯打开
  }
  if (Serial.available()) {
    SIM800C.write(Serial.read());
//    incomingByte = Serial.read();
//    Serial.print("I received: ");
//    Serial.println(incomingByte, DEC);
//    digitalWrite(13, !digitalRead(13));
  }

  Infrared_NUM = digitalRead(Infrared);//检测启动开关
  if(Infrared_NUM == LOW){
   // sendMeg();//发送短信例程代码
    SIM800C.println("AT");
     delay(2000);
    SIM800C.println("ATD12345678900;\r");//12345678900改成你要拨打的电话号码
    digitalWrite(12,HIGH);
    delay(5000);
    while(!digitalRead(Infrared));
    digitalWrite(12,LOW);
    //SIM800C.println("ATH");
    delay(1000);
  }
}

//发送短信例程代码
void sendMeg()
  {

  SIM800C.println("AT");
  delay(2000);
  SIM800C.println("AT+CMGF=1");
  delay(2000);
  SIM800C.println("AT+CMGS=\"12345678900\"");//这里改成你的号码
  delay(2000);
  SIM800C.print("Test\r\n");//这里写内容
  delay(2000);
  SIM800C.write(0x1A);//发送：0x1A，即“CTRL+Z”的键值，用于告诉 SIM800C，要执行发送操作
                      //发送： 0x1B，即“ESC”的键值，用于告诉 SIM800C，取消本次操作，不执行发送。
  }

在这里我们发送了一个AT命令，SIM800C返回一个Ok。再发送一个AT+GSV，返回：

　　13:33:20.943 -> SIMCOM_Ltd

　　13:33:20.943 -> SIMCOM_SIM800C

　　13:33:20.979 -> Revision:1418B06SIM800C24

　　通讯成功。任务初步完成。

//参考资料

//指令https://blog.****.net/cqdawnxsg/article/details/80680270

//https://www.cnblogs.com/xiaqiuchu/p/11568269.html

//https://www.arduino.cn/thread-6985-1-1.html