嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

时间:2022-01-01 18:40:01

 

本文将介绍通过完全手动定制内核,在此基础上添加 busybox ,并实现远程登陆,使裁剪的 linux 能够运行 nginx 。

在此之前介绍一下 linux 系统的启动流程。

linux系统启动流程
POST
-->BIOS(BOOT Sequence)-->MBR(bootloader,446个字节)-->kernel-->initrd(initramfs)-->(ROORFS)/sbin/init(/etc/inittab)

注:以上linux启动流程只是针对于centos6系列基于upstart流程的2.6内核,centos7使用了stytemd和此稍有不同。

关于启动流程详情参考另外一片文章:http://www.cnblogs.com/sysk/p/4778976.html

 

开始:

为虚拟机准备一块 1G (大小自定)的硬盘 为新的硬盘分区

/dev/sdb1=50M 剩余的容量全部给 /dev/sdb2

echo -e "n \n p \n 1 \n \n +50M \n n \n p \n 2 \n \n \n w \n" |fdisk /dev/sdb

查看结果:

Device Boot           Start         End      Blocks   Id  System

/dev/sdb1 1 7 56196 83 Linux

/dev/sdb2 8 130 987997+ 83 Linux

格式化分区

mke2fs  -t ext4 /dev/sdb1

mke2fs
-t ext4 /dev/sdb2

安装 grub 引导程序

mkdir /mnt/boot

mkdir
/mnt/sysroot

挂载 /dev/sdb1  到  /mnt/boot

mount /dev/sdb1 /mnt/boot

grub
-install --root-directory=/mnt /dev/sdb

执行结果如下

[root@localhost ~]# grub-install --root-directory=/mnt /dev/sdb

Probing devices to guess BIOS drives. This may take a
long time.

Installation finished. No error reported.

This
is the contents of the device map /mnt/boot/grub/device.map.

Check
if this is correct or not. If any of the lines is incorrect,

fix it and re
-run the script `grub-install'.

(fd0)
/dev/fd0

(hd0)
/dev/sda

(hd1)
/dev/sdb

查看是否安装成功

[root@localhost ~]# ls /mnt/boot/grub/

device.map fat_stage1_5 iso9660_stage1_5 minix_stage1_5 stage1ufs2_stage1_5 xfs_stage1_5

e2fs_stage1_5 ffs_stage1_5 jfs_stage1_5 reiserfs_stage1_5 stage2 vstafs_stage1_5

查看自己的硬件类型(我是基于VM10的)

[root@localhost ~]# lspci

00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02)

00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II]

00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)

00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter

00:03.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02)

00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service

00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01)

00:06.0 USB controller: Apple Inc. KeyLargo/Intrepid USB

00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 08)

00:14.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI

 

编译内核:

安装必要的开发工具和依赖包:

yum install perl
yum install bc
yum insatll gcc
-c++
yum install ncurses
-devel
yum groupinstall
"Development Libraries" " Development Tools"

下载内核源码后开始:

[root@localhost ~]# ln -sv /usr/src/linux-3.12.26/ /usr/src/linux

`
/usr/src/linux' -> `/usr/src/linux-3.12.26/'

[root@localhost
~]# cd /usr/src/linux

[root@localhost linux]# ls

arch COPYING crypto drivers fs init Kbuild kernel MAINTAINERS mm README samples security tools virt

block CREDITS Documentation firmware include ipc Kconfig lib Makefile net REPORTING
-BUGS scripts sound usr

[root@localhost linux]# make allnoconfig

HOSTCC scripts
/basic/fixdep

HOSTCC scripts
/kconfig/conf.o

SHIPPED scripts
/kconfig/zconf.tab.c

SHIPPED scripts
/kconfig/zconf.lex.c

SHIPPED scripts
/kconfig/zconf.hash.c

HOSTCC scripts
/kconfig/zconf.tab.o

HOSTLD scripts
/kconfig/conf

scripts
/kconfig/conf --allnoconfig Kconfig

#

# configuration written to .config

#
[root@localhost linux]# make menuconfig

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

下面开始配置所有功能直接编译进内核

 

 嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

 

进入 General setup  选项

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

返回首界面进入 Processor type and features

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

进入 Processor family (Generic-x86-64) 选择 cpu 类型 默认即可

返回首界面进入 Bus options (PCI etc.)

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

返回首界面进入  Executable file formats / Emulations

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

返回首界面进入 Networking support --->  Networking options  

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

返回首界面进入  Device Drivers  --->Generic Driver Options

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

返回上级界面

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

进入scsi device support

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

返回上级进入 Network device support--->   Ethernet driver support (NEW)

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

返回到 Network device support 此界面下选择 Input device suppor t

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

返回上级添加 usb 支持  USB support

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

返回首界面 File systems 

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

退出保存配置

[root@localhost linux]# make

[root@localhost linux]# make bzImage

make[
1]: Nothing to be done for `all'.

make[
1]: Nothing to be done for `relocs'.

CHK include
/config/kernel.release

CHK include
/generated/uapi/linux/version.h

CHK include
/generated/utsrelease.h

CALL scripts
/checksyscalls.sh

CHK include
/generated/compile.h

make[
3]: `arch/x86/realmode/rm/realmode.bin' is up to date.

Kernel: arch
/x86/boot/bzImage is ready (#1)

[root@localhost linux]# cp .
/arch/x86/boot/bzImage /mnt/boot

[root@localhost linux]# ls
/mnt/boot/

bzImage grub lost
+found

 

为新系统添加 rootfs  及 二进制程序 由 busybox 提供

[root@localhost ~]# tar -xf busybox-1.22.1.tar.bz2 -C /usr/src/

[root@localhost
~]# ls /usr/src/

busybox
-1.22.1 linux linux-3.12.26

busybox
-1.22.1.tar.bz2 glibc-static-2.12-1.132.el6.x86_64.rpm mariadb-5.5.36-linux-x86_64.tar.gz

[root@localhost
~]# cd /usr/src/busybox-1.22.1/

[root@localhost busybox
-1.22.1]# ls

applets configs editors libbb Makefile.custom printutils shell

 

编译 busybox

[root@localhost linux-3.12.26]# make menuconfig

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

进入 Busybox Settings ---->Build Options

此处需要选择 

Busybox Settings --> Build Options -->  Build BusyBox as a static binary (no shared libs)

安装glibc静态支持

yum install glibc-static
[root@localhost busybox-1.22.1]# make

[root@localhost busybox
-1.22.1]# make install

 

此时会在当前目录生成 _install 目录

[root@localhost busybox-1.22.1]# ls _install/

bin linuxrc sbin usr

 

挂载 /dev/sdb2  到   /mnt/sysroot

[root@localhost busybox-1.22.1]# mount /dev/sdb2 /mnt/sysroot/

[root@localhost busybox
-1.22.1]# cp -a ./_install/* /mnt/sysroot/

[root@localhost busybox-1.22.1]# ls /mnt/sysroot/

bin linuxrc lost+found sbin usr

[root@localhostbusybox-1.22.1]#mkdir -pv /mnt/sysroot/{etc,root,mnt,media,proc,sys,dev,home,lib,lib64,var,tmp}

 

由于 busybox 启动时默认的 init 程序为 /etc/init.d/rcS

[root@localhost busybox-1.22.1]# mkdir -pv /mnt/sysroot/etc/init.d

mkdir: created directory `
/mnt/sysroot/etc/init.d'

[root@localhost busybox
-1.22.1]# vim /mnt/sysroot/etc/init.d/rcS

#
!/bin/sh

mount
-n -t ext4 -o remount,rw /dev/sda2 /

mount
-n -t ext4 /dev/sda1 /boot

mount
-n -t tmpfs none /dev

mount
-n -t proc proc /proc

mount
-n -t sysfs sysfs /sys

mkdir
/dev/pts/

mount
-n -t devpts devpys /dev/pts

[
-r /etc/sysconfig/network ]&&source /etc/sysconfig/network

if [ ! -z $HOSTNAME ];then

/bin/hostname $HOSTNAME

else

/bin/hostname localhost

fi

 

[root@localhost busybox-1.22.1]# vim /mnt/sysroot/etc/profile

export PS1
="[\u@\h \w]\$"

[root@localhost linux]# mkdir
-pv /mnt/sysroot/etc/sysconfig

mkdir: created directory `
/mnt/sysroot/etc/sysconfig'

[root@localhost linux]# vim
/mnt/sysroot/etc/sysconfig/network

HOSTNAME
=www.mylinux.com

 

编辑 grub 配置文件

[root@localhost busybox-1.22.1]# vim /mnt/boot/grub/grub.conf

default=0

timeout
=5

title busy
-box-1.0

root(hd0,
0)

kernel
/bzImage ro root=/dev/sda2

 

先测试下看能否启动

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

下面使其能够以用户名密码进行登录

[root@localhost ~]# vim /mnt/sysroot/etc/inittab

::sysinit:
/etc/init.d/rcS

tty1::respawn:
/sbin/getty 19200 tty1

tty2::respawn:
/sbin/getty 19200 tty2

 

为其提供 /etc/passwd /etc/shadow /etc/group /etc/gshadow

直接从当前系统复制

[root@localhost ~]# cp -p /etc/passwd /mnt/sysroot/etc/

[root@localhost
~]# cp -p /etc/shadow /mnt/sysroot/etc/

[root@localhost
~]# cp -p /etc/group /mnt/sysroot/etc/

[root@localhost
~]# cp -p /etc/gshadow /mnt/sysroot/etc/

 也可以将上面四个文件分别用grep复制过去 如果嫌弃本机这些文件里面太多东西的话

 

grep  "^root"  /etc/shadow  > mnt/sysroot/etc/shadow

 

编辑 /mnt/sysroot/etc/passwd  将登录 shell 改为 /bin/sh

测试是否成功

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

正常登录

下面为其提供远程连接功能

编译安装 dropbear ( ssh )

为了进行登录名解析需要  linss 库文件和 /etc/nsswitch.conf

启用网络功能

[root@localhost ~]# cd dropbear-2014.65

.
/configure

make PROGRAMS
="dropbear dbclient dropbearkey dropbearconvert scp"

[root@localhost dropbear
-2014.65]# make install

 

默认安装在 /usr/local/{bin,sbin }

将此应用移植到目标系统移植脚本如下

#!/bin/bash
#

MntDIR1
="/mnt/boot"

MntDIR2
="/mnt/sysroot"

PORAPP ()

{

read
-p "Plz input the app: " APPLI

until [ "$APPLI" == quit ];do

while true;do

if which --skip-alias $APPLI ;then

WHERE
=$(which --skip-alias $APPLI)

DIRAPP
=$(dirname $WHERE)

[
-d ${MntDIR2}${DIRAPP} ]||mkdir -p ${MntDIR2}${DIRAPP}

[
-e ${MntDIR2}${WHERE} ]||cp $WHERE ${MntDIR2}${DIRAPP}

LIBS
=$(ldd $WHERE|grep -oE "(/[[:alnum:]]*/[^[:space:]]*[[:space:]])")

for i in $LIBS;do

DIRLIB
=$(dirname $i)

[
-d ${MntDIR2}$DIRLIB ]||mkdir -p ${MntDIR2}$DIRLIB

cp $i ${MntDIR2}$i

done

read
-p "Do you want to another app? or quit: " APPLI

continue
2

else

read
-p "Input is not app!! Plz input again or quit: " APPLI

continue
2

fi

done

done

}

##################MAIN##################

MAIN ()

{
PORAPP

}

MAIN

 

运行脚本

[root@localhost dropbear-2014.65]# bash 123.sh

bash:
123.sh: No such file or directory

[root@localhost dropbear
-2014.65]# bash /root/123.sh

Plz input the app:
/usr/local/bin/dbclient

/usr/local/bin/dbclient

Do you want to another app
? or quit: /usr/local/bin/dropbearkey

/usr/local/bin/dropbearkey

Do you want to another app
? or quit: /usr/local/bin/dropbearconvert

/usr/local/bin/dropbearconvert

Do you want to another app
? or quit: /usr/local/sbin/dropbear

/usr/local/sbin/dropbear

Do you want to another app
? or quit: quit

 

查看移植结果

[root@localhost dropbear-2014.65]# ls /mnt/sysroot/usr/local/{bin,sbin}

/mnt/sysroot/usr/local/bin:

dbclient dropbearconvert dropbearkey

/mnt/sysroot/usr/local/sbin:

dropbear

[root@localhost dropbear
-2014.65]# ls /mnt/sysroot/lib64/

ld-linux-x86-64.so.2 libcrypt.so.1 libc.so.6 libdl.so.2 libfreebl3.so libutil.so.1 libz.so.1

 

创建主机密钥

[root@localhost dropbear-2014.65]# mkdir /mnt/sysroot/etc/dropbear

[root@localhostdropbear
-2014.65]#

dropbearkey
-t dss -f /mnt/sysroot/etc/dropbear/dropbear_dss__host_key

[root@localhost dropbear
-2014.65]#

dropbearkey
-t rsa -f /mnt/sysroot/etc/dropbear/dropbear_rsa__host_key

 

移植 linss 库

[root@localhost dropbear-2014.65]# find  /lib64/libnss* -exec cp {} /mnt/sysroot/lib64/ \;

[root@localhost dropbear
-2014.65]# find /usr/lib64/libnss* -exec cp {} /mnt/sysroot/usr/lib64/ \;

 

创建 /etc/nsswitch.conf

passwd:     files

shadow: files

group: files

 

编辑 /etc/init.d/rcS 添加如下内容

ifconfig eth0 192.168.253.22 netmask 255.255.255.0 up

ifconfig lo 127.0.0.0 netmask 255.0.0.0

 

/usr/local/sbin/dropbear -E  验证

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

移植 nginx 到目标机

编译安装

./confgiure --prefix=/usr/local/nginx --without-httpd_rewrite_module

make && make install

 

运行移植脚本输入 /usr/local/nginx/sbin/nginx

cp -a -r /usr/local/nginx/* /mn t/sysroot/usr/local/nginx/

完成测试

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

客户端访问测试

嵌入式之Linux系统裁剪和定制---(kernel+busyboxy+dropbear+nginx)

整个过程完毕

 

 

 

 

遇到的问题:

在做完整个系统之后重启出现了这个报错

VFS: Cannot open root device "sda2" or unknown-block(0,0)
Please append a correct
"root=" boot option;here are the available partition 0b00 1048575 sr0 driver: sr
kernal panic
- not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

搞了好几天最后终于找到原因:

找到虚拟机配置文件的“.vmx",vmware默认的是LSI Logic,找到 ".vmx" 文件 里的scsi0.virtualDev = "lsilogic" 
改为 scsi0.virtualDev = "buslogic“

详情参照一下摘抄:

这两天一直在安装lfs6.2,安装到最后编译完内核,修改完fstab,最后安装grub后,启动lfs报错提示   
VFS:Cannot open root device
"sda" or unknow-block(0,0)
Please append a correct
"root=" boot option
kernel panic:VFS:Unable to mount root fs on unknown
-block(0,0)
看到这个错误的时候,我快崩溃了,我等了这么久,到最后一步出现了这个错误。大概意思是没有把root文件系统所在的硬盘控制器的驱动编译到内核中去,编译的时候我选择了scsi驱动了很奇怪,于是开始goole,baidu得到结果,大多都是集中在:
Device Drivers
--->SCSI device support--->SCSI disk support
Device Drivers
--->SCSI device support--->SCSI low-level drivers--->BusLogic SCSI support


一、磁盘(!!!)
在选择模块前,要先弄清楚VMware虚拟机的硬件类型,下面这个表是VMware6中自定义虚拟机配置时给出的配置,不难发现当您使用 VMware推荐向导给出的配置时,实际使用的是SCSI类型设备中的LSI Logic设备。这里要注意的一个地方是,既然有两个SCSI设备能够供其选择,那么该如何判断呢?很简单,因为他是通过内核主版本号来划分的。感兴趣的 朋友能够通过新建虚拟机Custom
-Linux下Version列表中Other Linux2.6.X kernel 和 Other Linux2.4.X kernel来比较。2.4内核之前使用BusLogic,2.6内核使用的是 LSI Logic 。
VMware
6.0:
I
/O ADapter Types
IDE adapter: ATAPI
SCSI adapter: BusLogic
LSI Logic
这是Other Linux2.
6.X kernel配置系统信息
00:10.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 01)

这是Other Linux2.
4.X kernel配置系统信息
00:10.0 SCSI storage controller: BusLogic BT-946C (BA80C30) [MultiMaster 10] (rev 01)
现在分别介绍模块选择路径
这个是SCSI磁盘设备模块,必须选择。
Linux Kernel Configuration
-> Device Drivers
-> SCSI device support
- > SCSI disk support
这个是BusLogic设备驱动模块。使用这个设备的的朋友需要选取。
Linux Kernel Configuration
-> Device Drivers
-> SCSI device support
-> SCSI low-level drivers
->
BusLogic SCSI support (这里一定要选上)
这个是LSI Logic设备驱动模块。使用这个设备的的朋友需要选取。
Linux Kernel Configuration
-> Device Drivers
-> Fusion MPT device support
-> Fusion MPT (base + ScsiHost) drivers

我的内核是kernel
-2.6.16.27,但是安装了上面提示的Fusion MPT (base + ScsiHost) drivers。问题依旧存在.所以我修改虚拟机的“.vmx",vmware默认的是LSI Logic,找到 ".vmx" 文件 里的scsi0.virtualDev = "lsilogic"
改为 scsi0.virtualDev = "buslogic
从新编译内核,启动系统`终于跳过了

 

另一个问题是关于网卡的:

  这个设备和内核版本没有关系,下面是系统信息参考:

02:00.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 10)
  
  Linux Kernel Configuration
  
-> Device Drivers
    
-> Networking support
      
-> Ethernet (10 or 100Mbit)

-> [*] EISA, VLB, PCI and on board controllers
-> <*> AMD PCnet32 PCI support

-> <*> AMD 8111 (new PCI lance) support



VMWare 所支持的网卡类型
它默认是虚拟的AMD PCNet AM79C970A网卡,但也可以改变网卡配置,虚拟出Intel(R) PRO
/1000和VMware PCI Ethernet Adapter网卡。

如果在.vmx文件中用如下语句指定:

ethernet0.virtualDev
= "e1000"

其值为e1000指定网卡类型为Intel(R) PRO
/1000

其值为vlance指定网卡类型为AMD PCNet AM79C970A(默认为此项)

其值为vmxnet指定网卡类型为VMware PCI Ethernet Adapter

我的网卡就是没有识别,在vm配置文件中加上

ethernet0.virtualDev = "e1000"
就可以识别到网卡了。