大纲
一、环境准备
二、拓扑准备
三、前提条件
四、安装相关软件
五、配置 heartbeat
六、测试Web集群
七、问题汇总
八、共享存储
一、环境准备
1.操作系统
CentOS 5.5 X86_64 最小化安装
说明：一般Heartbeat v2.x 都安装在CentOS 5.x系列中，而CentOS 6.x中都用Heartbeat v3.x。
2.相关软件
Heartbeat 2.1.4
Apache 2.2.3
3.配置epel YUM源（两节点都要配置）
node1,node2:
[root@node src]# wget http://download.fedoraproject.org/pub/epel/5/x86_64/epel-release-5-4.noarch.rpm[root@node src]# rpm -ivh epel-release-5-4.noarch.rpm
warning: epel-release-5-4.noarch.rpm: Header V3 DSA signature: NOKEY, key ID 217521f6
Preparing... ########################################### [100%]
1:epel-release ########################################### [100%]
[root@node src]# rpm --import /etc/pki/rpm-gpg/RPM-GPG-KEY-CentOS-5
[root@node src]# yum list
4.关闭防火墙与SELinux （两节点都要配置）
node1,node2:
[root@node ~]# service iptables stop [root@node ~]# vim /etc/selinux/config# This file controls the state of SELinux on the system. # SELINUX= can take one of these three values: # enforcing - SELinux security policy is enforced. # permissive - SELinux prints warnings instead of enforcing. # disabled - SELinux is fully disabled. SELINUX=disabled # SELINUXTYPE= type of policy in use. Possible values are: # targeted - Only targeted network daemons are protected. # strict - Full SELinux protection. SELINUXTYPE=targeted
二、拓扑准备
说明：有两个节点分别为node1与node2，VIP为192.168.18.200,测试机是一台Windows主机，NFS服务器为192.168.18.208
三、前提条件（两节点都要配置）
1.节点之间主机名互相解析
node1,node2:
[root@node ~]# vim /etc/hosts# Do not remove the following line, or various programs # that require network functionality will fail. 127.0.0.1 localhost.localdomain localhost ::1 localhost6.localdomain6 localhost6 192.168.18.201 node1.test.com node1 192.168.18.202 node2.test.com node2
2.节点之间时间得同步
node1,node2:
[root@node ~]# yum -y install ntp[root@node ~]# ntp 210.72.145.44[root@node ~]# date 2013年 08月 07日 星期三 16:06:30 CST
3.节点之间配置SSH互信
node1:
[root@node1 ~]# ssh-keygen -t rsa -f ~/.ssh/id_rsa -P ''[root@node1 ~]# ssh-copy-id -i .ssh/id_rsa.pub root@node2.test.com[root@node1 ~]# ssh node2[root@node2 ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:0C:29:EA:CE:79 inet addr:192.168.18.202 Bcast:192.168.18.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:feea:ce79/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:41736 errors:0 dropped:0 overruns:0 frame:0 TX packets:36201 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:35756480 (34.1 MiB) TX bytes:5698609 (5.4 MiB)lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)
node2:
[root@node2 ~]# ssh-keygen -t rsa -f ~/.ssh/id_rsa -P ''[root@node2 ~]# ssh-copy-id -i .ssh/id_rsa.pub root@node1.test.com[root@node2 ~]# ssh node1[root@node1 ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:0C:29:23:76:4D inet addr:192.168.18.201 Bcast:192.168.18.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe23:764d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:35226 errors:0 dropped:0 overruns:0 frame:0 TX packets:30546 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32941174 (31.4 MiB) TX bytes:4670062 (4.4 MiB)lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)
四、安装相关软件 （两节点都要安装）
1.heartbeat 安装组件说明
heartbeat 核心组件 *
heartbeat-devel 开发包
heartbeat-gui 图形管理接口 *
heartbeat-ldirectord 为lvs高可用提供规则自动生成及后端realserver健康状态检查的组件
heartbeat-pils 装载库插件接口 *
heartbeat-stonith 爆头接口 *
注：带*表示必须安装
2.安装heartbeat
node1,node2:
[root@node ~]# yum -y install heartbeat*
3.安装httpd
node1:
[root@node1~]# yum install -y httpd[root@node1 ~]# service httpd start 启动 httpd： [确定] [root@node1 ~]# echo "<h1>node1.test.com</h1>" > /var/www/html/index.html
测试
[root@node1 ha.d]# service httpd stop 停止 httpd： [确定] [root@node1 ha.d]# chkconfig httpd off [root@node1 ha.d]# chkconfig httpd --list httpd 0:关闭 1:关闭 2:关闭 3:关闭 4:关闭 5:关闭 6:关闭
说明：测试完成后关闭服务，并让其开机不启动（注，httpd由heartbeat管理）
node2:
[root@node2~]# yum install -y httpd[root@node2 ~]# service httpd start 启动 httpd： [确定] [root@node2 ~]# echo "<h1>node2.test.com</h1>" > /var/www/html/index.html
测试
[root@node2 ha.d]# service httpd stop停止 httpd： [确定][root@node2 ha.d]# chkconfig httpd off[root@node2 ha.d]# chkconfig httpd --listhttpd 0:关闭 1:关闭 2:关闭 3:关闭 4:关闭 5:关闭 6:关闭
说明：测试完成后关闭服务，并让其开机不启动（注，httpd由heartbeat管理）
五、配置 heartbeat
1.配置文件说明
[root@node1 ~]# cd /etc/ha.d/ [root@node1 ha.d]# ls harc rc.d README.config resource.d shellfuncs shellfuncs.rpmsave、
说明：安装好的heartbeat默认是没有配置文件的，但提供了配置文件样本
[root@node1 ha.d]# cd /usr/share/doc/heartbeat-2.1.4/ [root@node1 heartbeat-2.1.4]# ls apphbd.cf COPYING faqntips.txt HardwareGuide.html hb_report.txt README rsync.txt authkeys COPYING.LGPL GettingStarted.html HardwareGuide.txt heartbeat_api.html Requirements.html startstop AUTHORS DirectoryMap.txt GettingStarted.txt haresources heartbeat_api.txt Requirements.txt ChangeLog faqntips.html ha.cf hb_report.html logd.cf rsync.html[root@node1 heartbeat-2.1.4]# cp authkeys ha.cf haresources /etc/ha.d/
说明：其中有三个配置文件是我们需要的分别为，authkeys、ha.cf、haresources
authkeys #是节点之间的认证key文件，我们不能让什么服务器都加入集群中来，加入集群中的节点都是需要认证的
ha.cf #heartbeat的主配置文件
haresources #集群资源管理配置文件（在heartbeat所有版本中都是支持haresources来配置集群中的资源的）
2.配置authkeys文件
[root@node1 ha.d]# dd if=/dev/random bs=512 count=1 | openssl md5 #生成密钥随机数 0+1 records in 0+1 records out 128 bytes (128 B) copied, 0.000214 seconds, 598 kB/s a4d20b0dd3d5e35e0f87ce4266d1dd64
[root@node1 ha.d]# vim authkeys#auth 1 #1 crc #2 sha1 HI! #3 md5 Hello!auth 11 md5 a4d20b0dd3d5e35e0f87ce4266d1dd64
[root@node1 ha.d]# chmod 600 authkeys #修改密钥文件的权限为600 [root@node1 ha.d]# ll 总计 56 -rw------- 1 root root 691 08-07 16:45 authkeys -rw-r--r-- 1 root root 10539 08-07 16:42 ha.cf -rwxr-xr-x 1 root root 745 2010-03-21 harc -rw-r--r-- 1 root root 5905 08-07 16:42 haresources drwxr-xr-x 2 root root 4096 08-07 16:21 rc.d -rw-r--r-- 1 root root 692 2010-03-21 README.config drwxr-xr-x 2 root root 4096 08-07 16:21 resource.d -rw-r--r-- 1 root root 7862 2010-03-21 shellfuncs -rw-r--r-- 1 root root 7862 2010-03-21 shellfuncs.rpmsave
3.配置ha.cf文件
[root@node1 ha.d]# vim ha.cf
主要修改两处（其它都可以默认）：
(1).修改心跳信息的传播方式（这里是组播）
mcast eth0 225.100.100.100 694 1 0
(2).配置集群中的节点数
node node1.test.com node node2.test.com
4.配置haresources文件
[root@node1 ha.d]# vim haresourcesnode1.test.com IPaddr::192.168.18.200/24/eth0 httpd
5.复制以上三个配置文件到node2上
[root@node1 ha.d]# scp authkeys ha.cf haresources node2:/etc/ha.d/ authkeys 100% 691 0.7KB/s 00:00 ha.cf 100% 10KB 10.4KB/s 00:00 haresources 100% 5957 5.8KB/s 00:00 [root@node1 ha.d]# ssh node2 Last login: Wed Aug 7 16:13:44 2013 from node1.test.com [root@node2 ~]# ll /etc/ha.d/ 总计 56 -rw------- 1 root root 691 08-07 17:12 authkeys -rw-r--r-- 1 root root 10614 08-07 17:12 ha.cf -rwxr-xr-x 1 root root 745 2010-03-21 harc -rw-r--r-- 1 root root 5957 08-07 17:12 haresources drwxr-xr-x 2 root root 4096 08-07 16:24 rc.d -rw-r--r-- 1 root root 692 2010-03-21 README.config drwxr-xr-x 2 root root 4096 08-07 16:24 resource.d -rw-r--r-- 1 root root 7862 2010-03-21 shellfuncs -rw-r--r-- 1 root root 7862 2010-03-21 shellfuncs.rpmsave
6.启动node1与node2
[root@node1 ha.d]# ssh node2 "service heartbeat start"Strting High-Availability services:[确定]logd is already stopped[root@node1 ha.d]# service heartbeat start Starting High-Availability services: 2013/08/07_17:19:22 INFO: Resource is stopped [确定]
六、测试Web集群
1.查看启动的服务
[root@node1 ha.d]# netstat -ntulp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program nametcp 0 0 0.0.0.0:612 0.0.0.0:* LISTEN 2550/rpc.statd tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 2511/portmap tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 2845/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2889/sendmail: acce tcp 0 0 :::80 :::* LISTEN 8693/httpd tcp 0 0 :::22 :::* LISTEN 2832/sshd udp 0 0 0.0.0.0:43528 0.0.0.0:* 8278/heartbeat: wri udp 0 0 225.100.100.100:694 0.0.0.0:* 8278/heartbeat: wri udp 0 0 0.0.0.0:606 0.0.0.0:* 2550/rpc.statd udp 0 0 0.0.0.0:609 0.0.0.0:* 2550/rpc.statd udp 0 0 0.0.0.0:5353 0.0.0.0:* 3002/avahi-daemon:udp 0 0 0.0.0.0:111 0.0.0.0:* 2511/portmap udp 0 0 0.0.0.0:40439 0.0.0.0:* 3002/avahi-daemon:udp 0 0 0.0.0.0:631 0.0.0.0:* 2845/cupsd udp 0 0 :::37782 :::* 3002/avahi-daemon:udp 0 0 :::5353 :::* 3002/avahi-daemon:
2.查看IP
[root@node1 ha.d]# ifconfig eth0 Link encap:Ethernet HWaddr 00:0C:29:23:76:4D inet addr:192.168.18.201 Bcast:192.168.18.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe23:764d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:59888 errors:0 dropped:0 overruns:0 frame:0 TX packets:38388 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:41693748 (39.7 MiB) TX bytes:5689144 (5.4 MiB)eth0:0 Link encap:Ethernet HWaddr 00:0C:29:23:76:4D inet addr:192.168.18.200 Bcast:192.168.18.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:34 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3887 (3.7 KiB) TX bytes:3887 (3.7 KiB)
3.测试
4.故障演示
1).关闭node1上的heartbeat
[root@node1 ha.d]# service heartbeat stop #将node1中的heartbeat关闭 Stopping High-Availability services: [确定] [root@node1 ha.d]#
2).查看node2上的IP
[root@node2 ~]# ifconfig # 查看node2的IP，可以看到立即转移到node2上 eth0 Link encap:Ethernet HWaddr 00:0C:29:EA:CE:79 inet addr:192.168.18.202 Bcast:192.168.18.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:feea:ce79/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:69701 errors:0 dropped:0 overruns:0 frame:0 TX packets:44269 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:46270836 (44.1 MiB) TX bytes:6735723 (6.4 MiB)eth0:0 Link encap:Ethernet HWaddr 00:0C:29:EA:CE:79 inet addr:192.168.18.200 Bcast:192.168.18.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:34 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3887 (3.7 KiB) TX bytes:3887 (3.7 KiB)
3).测试
大家可以看到，集群已经转移到node2上，从而实现了Web高可用。
七、问题汇总
各位博友，可以从上面的实验中可以看出，此集群架构存在一重要问题？当主服器故障了或说宕机了，服务（这里是80端口）和VIP立即切换到从服务器上继续提供服务，这是没有问题的，若是这个集群提供的是论坛服务，一用户刚刚上传一附件到主服务器上，这时主服务器宕机了，用户一刷新发现刚刚上传的附件没有了，用户会怎么想呢？这会带来用户体验的缺失。那有博友会问了，那有没有什么方法解决这个问题呢？答案是肯定有的，基本上有两种解决方案，一种是各节点之间进行文件同步，另一种是各节点之间使用共享存储。下面我们就来说一说这两种方案。
第一种方案，我们说了使用节点间的文件同步，我们一般用Rsync+Inotify组合方案来解决节点之间的同步问题，但有个问题，我们说有极端一点，还是刚才论坛附件的问题，用户刚上传了附件，这时主服务器宕机了，还没有同步，用户看不到附件，还有一点情况，用户上传的附件比较大，各节点之间正在同步，这时主服务器宕机了，用户看到的附件是不完整，也不能达到很好的用户体验。而且节点之间同步，还会占用大量的带宽。说了这么多，我们总结一下，这种方案的优缺点吧，优点：可节点一台或多台服务器，节约成本，在小规模的集群中，文件同步效果还是不错的，在大规模的集群服务器不推荐使用，缺点：节点之间同步文件，占用大量的网络带宽，降低整体集群性能，在比较烦忙的集群中不推荐使用。
第二种方案，就是我们所说的共享存储方案了，共享存储方案也有两种方案，一种是文件级别的共享存储（如，NFS文件服务器），另一种是块级别的共享存储（如，iscsi共享存储）。用这种方案就能很好的解决上述的问题，上面的集群中有两个节点，主节点与从节点共享一个文件服务器，当主节点提供服务时，文件服务器是挂载在主节点上，当主节点宕机了，从节点来提供服务，并挂载同一个文件服务器，这时我们就不用担心当主节点宕机了附件也没有了，因为我们使用的同一共享存储，只要附件上传到时服务器中，我们就能看，不用担心附件不存在，或说得同步附件的问题了。在高可用集群中我比较推荐共享存储。下面我们就用NFS来演示一下各节点之间挂载共享存储。
八、共享存储
１.配置NFS服务器
[root@nfs ~]# mkdir -pv /webmkdir: 已创建目录 “/web” [root@nfs ~]# vim /etc/exports/web/ 192.168.18.0/24(ro,async)[root@nfs /]# echo '<h1>Cluster NFS Server</h1>' > /web/index.html[root@nfs /]# /etc/init.d/portmap start启动 portmap： [确定][root@nfs /]# /etc/init.d/nfs start 启动 NFS 服务： [确定] 关掉 NFS 配额： [确定] 启动 NFS 守护进程： [确定] 启动 NFS mountd： [确定][root@nfs /]# showmount -e 192.168.18.208Export list for 192.168.18.208: /web 192.168.18.0/24
2.节点测试挂载
node1:
[root@node1 ~]# mount -t nfs 192.168.18.208:/web /mnt[root@node1 ~]# cd /mnt/ [root@node1 mnt]# ll 总计 4 -rw-r--r-- 1 root root 28 08-07 17:41 index.html [root@node1 mnt]# mount /dev/sda2 on / type ext3 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sda3 on /data type ext3 (rw) /dev/sda1 on /boot type ext3 (rw) tmpfs on /dev/shm type tmpfs (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw) 192.168.18.208:/web on /mnt type nfs (rw,addr=192.168.18.208) [root@node1 ~]# umount /mnt [root@node1 ~]# mount /dev/sda2 on / type ext3 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sda3 on /data type ext3 (rw) /dev/sda1 on /boot type ext3 (rw) tmpfs on /dev/shm type tmpfs (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw)
node2:
[root@node2 ~]# mount -t nfs 192.168.18.208:/web /mnt[root@node2 ~]# cd /mnt [root@node2 mnt]# ll 总计 4 -rw-r--r-- 1 root root 28 08-07 17:41 index.html [root@node2 mnt]# mount /dev/sda2 on / type ext3 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sda3 on /data type ext3 (rw) /dev/sda1 on /boot type ext3 (rw) tmpfs on /dev/shm type tmpfs (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw) 192.168.18.208:/web on /mnt type nfs (rw,addr=192.168.18.208)[root@node2 ~]# umount /mnt[root@node2 ~]# mount /dev/sda2 on / type ext3 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sda3 on /data type ext3 (rw) /dev/sda1 on /boot type ext3 (rw) tmpfs on /dev/shm type tmpfs (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw)
3.修改haresource文件
[root@node1 ~]# vim /etc/ha.d/haresourcesnode1.test.com IPaddr::192.168.18.200/24/eth0 Filesystem::192.168.18.95:/web::/var/www/html::nfs httpd
4.同步haresource配置文件
[root@node1 ~]# cd /etc/ha.d/[root@node1 ha.d]# scp haresources node2:/etc/ha.d/ haresources 100% 5964 5.8KB/s 00:00
5.重启一下heartbeat
[root@node1 ha.d]# ssh node2 "service heartbeat restart"Stopping High-Availability services: [确定] Waiting to allow resource takeover to complete: [确定] Starting High-Availability services: 2013/08/07_17:59:26 INFO: Running OK 2013/08/07_17:59:26 CRITICAL: Resource IPaddr::192.168.18.200/24/eth0 is active, and should not be! 2013/08/07_17:59:26 CRITICAL: Non-idle resources can affect data integrity! 2013/08/07_17:59:26 info: If you don't know what this means, then get help! 2013/08/07_17:59:26 info: Read the docs and/or source to /usr/share/heartbeat/ResourceManager for more details. CRITICAL: Resource IPaddr::192.168.18.200/24/eth0 is active, and should not be! CRITICAL: Non-idle resources can affect data integrity! info: If you don't know what this means, then get help! info: Read the docs and/or the source to /usr/share/heartbeat/ResourceManager for more details. 2013/08/07_17:59:26 CRITICAL: Non-idle resources will affect resource takeback! 2013/08/07_17:59:26 CRITICAL: Non-idle resources may affect data integrity! [确定] [root@node1 ha.d]# service heartbeat restart Stopping High-Availability services: [确定] Waiting to allow resource takeover to complete: [确定] Starting High-Availability services: 2013/08/07_17:59:56 INFO: Resource is stopped [确定] [root@node1 ha.d]#
6.查看一下端口
[root@node1 ha.d]# netstat -ntulpActive Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program nametcp 0 0 0.0.0.0:56610 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:612 0.0.0.0:* LISTEN 2550/rpc.statd tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 2511/portmap tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 2845/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2889/sendmail: acce tcp 0 0 :::80 :::* LISTEN 11205/httpd tcp 0 0 :::22 :::* LISTEN 2832/sshd udp 0 0 0.0.0.0:43027 0.0.0.0:* - udp 0 0 225.100.100.100:694 0.0.0.0:* 10659/heartbeat: wr udp 0 0 0.0.0.0:606 0.0.0.0:* 2550/rpc.statd udp 0 0 0.0.0.0:609 0.0.0.0:* 2550/rpc.statd udp 0 0 0.0.0.0:5353 0.0.0.0:* 3002/avahi-daemon:udp 0 0 0.0.0.0:57068 0.0.0.0:* 10659/heartbeat: wr udp 0 0 0.0.0.0:111 0.0.0.0:* 2511/portmap udp 0 0 0.0.0.0:40439 0.0.0.0:* 3002/avahi-daemon:udp 0 0 0.0.0.0:631 0.0.0.0:* 2845/cupsd udp 0 0 :::37782 :::* 3002/avahi-daemon:udp 0 0 :::5353 :::* 3002/avahi-daemon:[root@node1 ha.d]#
7.测试一下Web服务
[root@node1 ha.d]# mount/dev/sda2 on / type ext3 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sda3 on /data type ext3 (rw) /dev/sda1 on /boot type ext3 (rw) tmpfs on /dev/shm type tmpfs (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw) 192.168.18.208:/web on /var/www/html type nfs (rw,addr=192.168.18.208)
大家可以看到，顺利挂载并测试成功！
8.模拟故障并测试
(1).停止节点1上的heartbeat
[root@node1 ~]# service heartbeat stopStopping High-Availability services: [确定] logd is already stopped
(2).查看节点2的IP与服务
[root@node2 ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:0C:29:EA:CE:79 inet addr:192.168.18.202 Bcast:192.168.18.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:feea:ce79/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77896 errors:0 dropped:0 overruns:0 frame:0 TX packets:46970 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:47233291 (45.0 MiB) TX bytes:7348076 (7.0 MiB)eth0:0 Link encap:Ethernet HWaddr 00:0C:29:EA:CE:79 inet addr:192.168.18.200 Bcast:192.168.18.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8171 (7.9 KiB) TX bytes:8171 (7.9 KiB)[root@node2 ~]# netstat -ntulpActive Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program nametcp 0 0 0.0.0.0:34050 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 2537/portmap tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 2871/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2915/sendmail: acce tcp 0 0 0.0.0.0:638 0.0.0.0:* LISTEN 2576/rpc.statd tcp 0 0 :::80 :::* LISTEN 9291/httpd tcp 0 0 :::22 :::* LISTEN 2858/sshd udp 0 0 0.0.0.0:57488 0.0.0.0:* 8902/heartbeat: wri udp 0 0 0.0.0.0:48555 0.0.0.0:* 3028/avahi-daemon:udp 0 0 0.0.0.0:56756 0.0.0.0:* - udp 0 0 225.100.100.100:694 0.0.0.0:* 8902/heartbeat: wri udp 0 0 0.0.0.0:5353 0.0.0.0:* 3028/avahi-daemon:udp 0 0 0.0.0.0:111 0.0.0.0:* 2537/portmap udp 0 0 0.0.0.0:631 0.0.0.0:* 2871/cupsd udp 0 0 0.0.0.0:632 0.0.0.0:* 2576/rpc.statd udp 0 0 0.0.0.0:635 0.0.0.0:* 2576/rpc.statd udp 0 0 :::59997 :::* 3028/avahi-daemon:udp 0 0 :::5353 :::* 3028/avahi-daemon:
(3).测试服务
说明：大家可以看到，可以正常访问，这样我们就实现了heartbeat+httpd+nfs实现高可用的Web集群。希望通过上面的博文，大家基本了解高可用集群是怎么回事。^_^……
(4).重新启动node1上heartbeat
[root@node1 ~]# service heartbeat startStarting High-Availability services:2013/08/07_19:24:41 INFO: Resource is stopped [确定]
(5).查看日志
[root@node1 ~]# tail -f /var/log/messagesAug 7 19:24:45 node1 IPaddr[11796]: INFO: SuccessAug 7 19:24:45 node1 Filesystem[11932]: INFO: Resource is stoppedAug 7 19:24:45 node1 ResourceManager[11700]: info: Running /etc/ha.d/resource.d/Filesystem 192.168.18.208:/web /var/www/html nfs startAug 7 19:24:45 node1 Filesystem[12013]: INFO: Running start for 192.168.18.208:/web on /var/www/htmlAug 7 19:24:45 node1 Filesystem[12002]: INFO: SuccessAug 7 19:24:45 node1 ResourceManager[11700]: info: Running /etc/init.d/httpd startAug 7 19:24:45 node1 heartbeat: [11687]: info: local HA resource acquisition completed (standby).Aug 7 19:24:45 node1 heartbeat: [11661]: info: Standby resource acquisition done [foreign].Aug 7 19:24:45 node1 heartbeat: [11661]: info: Initial resource acquisition complete (auto_failback)Aug 7 19:24:45 node1 heartbeat: [11661]: info: remote resource transition completed.
(6).查看IP
[root@node1 ~]# ifconfigeth0 Link encap:Ethernet HWaddr 00:0C:29:23:76:4D inet addr:192.168.18.201 Bcast:192.168.18.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe23:764d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:86048 errors:0 dropped:0 overruns:0 frame:0 TX packets:42794 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:46010055 (43.8 MiB) TX bytes:6400751 (6.1 MiB)eth0:0 Link encap:Ethernet HWaddr 00:0C:29:23:76:4D inet addr:192.168.18.200 Bcast:192.168.18.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:100 errors:0 dropped:0 overruns:0 frame:0 TX packets:100 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10619 (10.3 KiB) TX bytes:10619 (10.3 KiB)
(7).查看服务
[root@node1 ~]# netstat -ntulpActive Internet connections (only servers)Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:612 0.0.0.0:* LISTEN 2550/rpc.statd tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 2511/portmap tcp 0 0 0.0.0.0:51217 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 2845/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2889/sendmail: accetcp 0 0 :::80 :::* LISTEN 12100/httpd tcp 0 0 :::22 :::* LISTEN 2832/sshd udp 0 0 225.100.100.100:694 0.0.0.0:* 11665/heartbeat: wrudp 0 0 0.0.0.0:36944 0.0.0.0:* 11665/heartbeat: wrudp 0 0 0.0.0.0:606 0.0.0.0:* 2550/rpc.statd udp 0 0 0.0.0.0:609 0.0.0.0:* 2550/rpc.statd udp 0 0 0.0.0.0:5353 0.0.0.0:* 3002/avahi-daemon:udp 0 0 0.0.0.0:111 0.0.0.0:* 2511/portmap udp 0 0 0.0.0.0:40439 0.0.0.0:* 3002/avahi-daemon:udp 0 0 0.0.0.0:631 0.0.0.0:* 2845/cupsd udp 0 0 0.0.0.0:45693 0.0.0.0:* - udp 0 0 :::37782 :::* 3002/avahi-daemon:udp 0 0 :::5353 :::* 3002/avahi-daemon:
(8).再测试一下
大家可以看到，依然可以测试成功，实现了Web的高可用，好了本次博文到这边全部结束！欢迎大家提出宝贵意见，多多交流，共同进步……
本文出自 “Share your knowledge …” 博客，请务必保留此出处http://freeloda.blog.51cto.com/2033581/1266552