6、CC2541修改按键调节广播发送功率例程为持续发送4DB的蓝牙基站

时间：2023-03-08 15:37:40
一、目的

在 OSAL操作系统-实验31 从机广播功率修改-（20141029更新）.zip 基础上进行修改，该工程是通过5向按键的上下按键来控制广播功率的加减，总共有4个档位。我们的目的是直接用最高功率进行广播。

二、涉及文件

下面几个文件是每个CC2541工程的主要文件（基本的修改都会在此）：

6、CC2541修改按键调节广播发送功率例程为持续发送4DB的蓝牙基站

其中:

  • xxx_Main.c只有main函数，
  • OSAL_SimpleBLEPeripheral.c中只有任务初始化函数，
  • simpleBLEPeripheral.c才是重点

　　6、CC2541修改按键调节广播发送功率例程为持续发送4DB的蓝牙基站

三、如何修改

整个工程是采用默认发射功率，然后通过有向按键控制gTxPower大小并通过HCI_EXT_SetTxPowerCmd(gTxPower);重新设置发射功率大小：

 if ( keys & HAL_KEY_UP )

 {

     HalLcdWriteString( "HAL_KEY_UP", HAL_LCD_LINE_5 );

     /*

     #define LL_EXT_TX_POWER_MINUS_23_DBM                   0 // -23dbm  功率 最小

     #define LL_EXT_TX_POWER_MINUS_6_DBM                    1 // -6dbm

     #define LL_EXT_TX_POWER_0_DBM                          2  // 0dbm

     #define LL_EXT_TX_POWER_4_DBM                          3  // +dbm  功率 最大

     */

     if(gTxPower < LL_EXT_TX_POWER_4_DBM)

     {

         gTxPower++;   //功率提高一档

         HCI_EXT_SetTxPowerCmd(gTxPower);

         HalLcdWriteStringValue( "TxPower: ", gTxPower, , HAL_LCD_LINE_7 );

     }

 }

因此，我们只要在GAPROLE_ADVERTISING事件下调用HCI_EXT_SetTxPowerCmd(gTxPower);将默认广播发送功率设置为4db即可（同时也要设置默认广播发送功率为4db:uint8 gTxPower = LL_EXT_TX_POWER_4_DBM;）！

 case GAPROLE_CONNECTED:

 {

     #if (defined HAL_LCD) && (HAL_LCD == TRUE)

     HalLcdWriteString( "Connected",  HAL_LCD_LINE_3 );

     HCI_EXT_SetTxPowerCmd(gTxPower);

     #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

 }

 break;

修改后simpleBLEPeripheral.c为：

 /**************************************************************************************************

   Filename:       simpleBLEPeripheral.c

   Revised:        $Date: 2010-08-06 08:56:11 -0700 (Fri, 06 Aug 2010) $

   Revision:       $Revision: 23333 $

   Description:    This file contains the Simple BLE Peripheral sample application

                   for use with the CC2540 Bluetooth Low Energy Protocol Stack.

   Copyright 2010 - 2013 Texas Instruments Incorporated. All rights reserved.

   IMPORTANT: Your use of this Software is limited to those specific rights

   granted under the terms of a software license agreement between the user

   who downloaded the software, his/her employer (which must be your employer)

   and Texas Instruments Incorporated (the "License").  You may not use this

   Software unless you agree to abide by the terms of the License. The License

   limits your use, and you acknowledge, that the Software may not be modified,

   copied or distributed unless embedded on a Texas Instruments microcontroller

   or used solely and exclusively in conjunction with a Texas Instruments radio

   frequency transceiver, which is integrated into your product.  Other than for

   the foregoing purpose, you may not use, reproduce, copy, prepare derivative

   works of, modify, distribute, perform, display or sell this Software and/or

   its documentation for any purpose.

   YOU FURTHER ACKNOWLEDGE AND AGREE THAT THE SOFTWARE AND DOCUMENTATION ARE

   PROVIDED 揂S IS?WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,

   INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, TITLE,

   NON-INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL

   TEXAS INSTRUMENTS OR ITS LICENSORS BE LIABLE OR OBLIGATED UNDER CONTRACT,

   NEGLIGENCE, STRICT LIABILITY, CONTRIBUTION, BREACH OF WARRANTY, OR OTHER

   LEGAL EQUITABLE THEORY ANY DIRECT OR INDIRECT DAMAGES OR EXPENSES

   INCLUDING BUT NOT LIMITED TO ANY INCIDENTAL, SPECIAL, INDIRECT, PUNITIVE

   OR CONSEQUENTIAL DAMAGES, LOST PROFITS OR LOST DATA, COST OF PROCUREMENT

   OF SUBSTITUTE GOODS, TECHNOLOGY, SERVICES, OR ANY CLAIMS BY THIRD PARTIES

   (INCLUDING BUT NOT LIMITED TO ANY DEFENSE THEREOF), OR OTHER SIMILAR COSTS.

   Should you have any questions regarding your right to use this Software,

   contact Texas Instruments Incorporated at www.TI.com.

 **************************************************************************************************/

 /*********************************************************************

  * INCLUDES

  */

 #include "bcomdef.h"

 #include "OSAL.h"

 #include "OSAL_PwrMgr.h"

 #include "OnBoard.h"

 #include "hal_adc.h"

 #include "hal_led.h"

 #include "hal_key.h"

 #include "hal_lcd.h"

 #include "gatt.h"

 #include "hci.h"

 #include "gapgattserver.h"

 #include "gattservapp.h"

 #include "devinfoservice.h"

 #include "simpleGATTprofile.h"

 #if defined( CC2540_MINIDK )

   #include "simplekeys.h"

 #endif

 #if defined ( PLUS_BROADCASTER )

   #include "peripheralBroadcaster.h"

 #else

   #include "peripheral.h"

 #endif

 #include "gapbondmgr.h"

 #include "simpleBLEPeripheral.h"

 #if defined FEATURE_OAD

   #include "oad.h"

   #include "oad_target.h"

 #endif

 /*********************************************************************

  * MACROS

  */

 /*********************************************************************

  * CONSTANTS

  */

 // How often to perform periodic event

 #define SBP_PERIODIC_EVT_PERIOD                   1000

 // What is the advertising interval when device is discoverable (units of 625us, 160=100ms)

 #define DEFAULT_ADVERTISING_INTERVAL          160

 // Limited discoverable mode advertises for 30.72s, and then stops

 // General discoverable mode advertises indefinitely

 #if defined ( CC2540_MINIDK )

 #define DEFAULT_DISCOVERABLE_MODE             GAP_ADTYPE_FLAGS_LIMITED

 #else

 #define DEFAULT_DISCOVERABLE_MODE             GAP_ADTYPE_FLAGS_GENERAL

 #endif  // defined ( CC2540_MINIDK )

 // Minimum connection interval (units of 1.25ms, 80=100ms) if automatic parameter update request is enabled

 #define DEFAULT_DESIRED_MIN_CONN_INTERVAL     80

 // Maximum connection interval (units of 1.25ms, 800=1000ms) if automatic parameter update request is enabled

 #define DEFAULT_DESIRED_MAX_CONN_INTERVAL     800

 // Slave latency to use if automatic parameter update request is enabled

 #define DEFAULT_DESIRED_SLAVE_LATENCY         0

 // Supervision timeout value (units of 10ms, 1000=10s) if automatic parameter update request is enabled

 #define DEFAULT_DESIRED_CONN_TIMEOUT          1000

 // Whether to enable automatic parameter update request when a connection is formed

 #define DEFAULT_ENABLE_UPDATE_REQUEST         TRUE

 // Connection Pause Peripheral time value (in seconds)

 #define DEFAULT_CONN_PAUSE_PERIPHERAL         6

 // Company Identifier: Texas Instruments Inc. (13)

 #define TI_COMPANY_ID                         0x000D

 #define INVALID_CONNHANDLE                    0xFFFF

 // Length of bd addr as a string

 #define B_ADDR_STR_LEN                        15

 #if defined ( PLUS_BROADCASTER )

   #define ADV_IN_CONN_WAIT                    500 // delay 500 ms

 #endif

 /*********************************************************************

  * TYPEDEFS

  */

 /*********************************************************************

  * GLOBAL VARIABLES

  */

 /*********************************************************************

  * EXTERNAL VARIABLES

  */

 /*********************************************************************

  * EXTERNAL FUNCTIONS

  */

 /*********************************************************************

  * LOCAL VARIABLES

  */

 static uint8 simpleBLEPeripheral_TaskID;   // Task ID for internal task/event processing

 static gaprole_States_t gapProfileState = GAPROLE_INIT;

 // GAP - SCAN RSP data (max size = 31 bytes)

 static uint8 scanRspData[] =

 {

   // complete name

   0x14,   // length of this data

   GAP_ADTYPE_LOCAL_NAME_COMPLETE,

   0x53,   // 'S'

   0x69,   // 'i'

   0x6d,   // 'm'

   0x70,   // 'p'

   0x6c,   // 'l'

   0x65,   // 'e'

   0x42,   // 'B'

   0x4c,   // 'L'

   0x45,   // 'E'

   0x50,   // 'P'

   0x65,   // 'e'

   0x72,   // 'r'

   0x69,   // 'i'

   0x70,   // 'p'

   0x68,   // 'h'

   0x65,   // 'e'

   0x72,   // 'r'

   0x61,   // 'a'

   0x6c,   // 'l'

   // connection interval range

   0x05,   // length of this data

   GAP_ADTYPE_SLAVE_CONN_INTERVAL_RANGE,

   LO_UINT16( DEFAULT_DESIRED_MIN_CONN_INTERVAL ),   // 100ms

   HI_UINT16( DEFAULT_DESIRED_MIN_CONN_INTERVAL ),

   LO_UINT16( DEFAULT_DESIRED_MAX_CONN_INTERVAL ),   // 1s

   HI_UINT16( DEFAULT_DESIRED_MAX_CONN_INTERVAL ),

   // Tx power level

   0x02,   // length of this data

   GAP_ADTYPE_POWER_LEVEL,

          // 0dBm

 };

 // GAP - Advertisement data (max size = 31 bytes, though this is

 // best kept short to conserve power while advertisting)

 static uint8 advertData[] =

 {

   // Flags; this sets the device to use limited discoverable

   // mode (advertises for 30 seconds at a time) instead of general

   // discoverable mode (advertises indefinitely)

   0x02,   // length of this data

   GAP_ADTYPE_FLAGS,

   DEFAULT_DISCOVERABLE_MODE | GAP_ADTYPE_FLAGS_BREDR_NOT_SUPPORTED,

   // service UUID, to notify central devices what services are included

   // in this peripheral

   0x03,   // length of this data

   GAP_ADTYPE_16BIT_MORE,      // some of the UUID's, but not all

   LO_UINT16( SIMPLEPROFILE_SERV_UUID ),

   HI_UINT16( SIMPLEPROFILE_SERV_UUID ),

 };

 // GAP - Advertisement data (max size = 31 bytes, though this is

 // best kept short to conserve power while advertisting)

 uint8 advertData_Ex[] =

 {

   // Flags; this sets the device to use limited discoverable

   // mode (advertises for 30 seconds at a time) instead of general

   // discoverable mode (advertises indefinitely)

   0x02,   // length of this data

   GAP_ADTYPE_FLAGS,

   DEFAULT_DISCOVERABLE_MODE | GAP_ADTYPE_FLAGS_BREDR_NOT_SUPPORTED,

   // service UUID, to notify central devices what services are included

   // in this peripheral

   0x0B,   // length of this data

   //下面总共自定义 8个字节

   0x00,   // 自定义

   0x00,   // 自定义

   0x00,   // 自定义

   0x00,   // 自定义

   0x00,   // 自定义

   0x00,   // 自定义

   0x00,   // 自定义

   0x00,   // 自定义

   GAP_ADTYPE_16BIT_MORE,      // some of the UUID's, but not all

   LO_UINT16( SIMPLEPROFILE_SERV_UUID ),

   HI_UINT16( SIMPLEPROFILE_SERV_UUID ),

 };

 // GAP GATT Attributes

 static uint8 attDeviceName[GAP_DEVICE_NAME_LEN] = "Simple BLE Peripheral";

 /*********************************************************************

  * LOCAL FUNCTIONS

  */

 static void simpleBLEPeripheral_ProcessOSALMsg( osal_event_hdr_t *pMsg );

 static void peripheralStateNotificationCB( gaprole_States_t newState );

 static void performPeriodicTask( void );

 static void simpleProfileChangeCB( uint8 paramID );

 //#if defined( CC2540_MINIDK )

 static void simpleBLEPeripheral_HandleKeys( uint8 shift, uint8 keys );

 //#endif

 #if (defined HAL_LCD) && (HAL_LCD == TRUE)

 static char *bdAddr2Str ( uint8 *pAddr );

 #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

 /*********************************************************************

  * PROFILE CALLBACKS

  */

 // GAP Role Callbacks

 static gapRolesCBs_t simpleBLEPeripheral_PeripheralCBs =

 {

   peripheralStateNotificationCB,  // Profile State Change Callbacks

   NULL                            // When a valid RSSI is read from controller (not used by application)

 };

 // GAP Bond Manager Callbacks

 static gapBondCBs_t simpleBLEPeripheral_BondMgrCBs =

 {

   NULL,                     // Passcode callback (not used by application)

   NULL                      // Pairing / Bonding state Callback (not used by application)

 };

 // Simple GATT Profile Callbacks

 static simpleProfileCBs_t simpleBLEPeripheral_SimpleProfileCBs =

 {

   simpleProfileChangeCB    // Charactersitic value change callback

 };

 /*********************************************************************

  * PUBLIC FUNCTIONS

  */

 /*********************************************************************

  * @fn      SimpleBLEPeripheral_Init

  *

  * @brief   Initialization function for the Simple BLE Peripheral App Task.

  *          This is called during initialization and should contain

  *          any application specific initialization (ie. hardware

  *          initialization/setup, table initialization, power up

  *          notificaiton ... ).

  *

  * @param   task_id - the ID assigned by OSAL.  This ID should be

  *                    used to send messages and set timers.

  *

  * @return  none

  */

 void SimpleBLEPeripheral_Init( uint8 task_id )

 {

   simpleBLEPeripheral_TaskID = task_id;

   // Setup the GAP

   VOID GAP_SetParamValue( TGAP_CONN_PAUSE_PERIPHERAL, DEFAULT_CONN_PAUSE_PERIPHERAL );

   // Setup the GAP Peripheral Role Profile

   {

     #if defined( CC2540_MINIDK )

       // For the CC2540DK-MINI keyfob, device doesn't start advertising until button is pressed

       uint8 initial_advertising_enable = FALSE;

     #else

       // For other hardware platforms, device starts advertising upon initialization

       uint8 initial_advertising_enable = TRUE;

     #endif

     // By setting this to zero, the device will go into the waiting state after

     // being discoverable for 30.72 second, and will not being advertising again

     // until the enabler is set back to TRUE

     uint16 gapRole_AdvertOffTime = ;

     uint8 enable_update_request = DEFAULT_ENABLE_UPDATE_REQUEST;

     uint16 desired_min_interval = DEFAULT_DESIRED_MIN_CONN_INTERVAL;

     uint16 desired_max_interval = DEFAULT_DESIRED_MAX_CONN_INTERVAL;

     uint16 desired_slave_latency = DEFAULT_DESIRED_SLAVE_LATENCY;

     uint16 desired_conn_timeout = DEFAULT_DESIRED_CONN_TIMEOUT;

     // Set the GAP Role Parameters

     GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &initial_advertising_enable );

     GAPRole_SetParameter( GAPROLE_ADVERT_OFF_TIME, sizeof( uint16 ), &gapRole_AdvertOffTime );

     GAPRole_SetParameter( GAPROLE_SCAN_RSP_DATA, sizeof ( scanRspData ), scanRspData );

     GAPRole_SetParameter( GAPROLE_ADVERT_DATA, sizeof( advertData ), advertData );

     GAPRole_SetParameter( GAPROLE_PARAM_UPDATE_ENABLE, sizeof( uint8 ), &enable_update_request );

     GAPRole_SetParameter( GAPROLE_MIN_CONN_INTERVAL, sizeof( uint16 ), &desired_min_interval );

     GAPRole_SetParameter( GAPROLE_MAX_CONN_INTERVAL, sizeof( uint16 ), &desired_max_interval );

     GAPRole_SetParameter( GAPROLE_SLAVE_LATENCY, sizeof( uint16 ), &desired_slave_latency );

     GAPRole_SetParameter( GAPROLE_TIMEOUT_MULTIPLIER, sizeof( uint16 ), &desired_conn_timeout );

   }

   // Set the GAP Characteristics

   GGS_SetParameter( GGS_DEVICE_NAME_ATT, GAP_DEVICE_NAME_LEN, attDeviceName );

   // Set advertising interval

   {

     uint16 advInt = DEFAULT_ADVERTISING_INTERVAL;

     GAP_SetParamValue( TGAP_LIM_DISC_ADV_INT_MIN, advInt );

     GAP_SetParamValue( TGAP_LIM_DISC_ADV_INT_MAX, advInt );

     GAP_SetParamValue( TGAP_GEN_DISC_ADV_INT_MIN, advInt );

     GAP_SetParamValue( TGAP_GEN_DISC_ADV_INT_MAX, advInt );

   }

   // Setup the GAP Bond Manager

   {

     uint32 passkey = ; // passkey "000000"

     uint8 pairMode = GAPBOND_PAIRING_MODE_WAIT_FOR_REQ;

     uint8 mitm = TRUE;

     uint8 ioCap = GAPBOND_IO_CAP_DISPLAY_ONLY;

     uint8 bonding = TRUE;

     GAPBondMgr_SetParameter( GAPBOND_DEFAULT_PASSCODE, sizeof ( uint32 ), &passkey );

     GAPBondMgr_SetParameter( GAPBOND_PAIRING_MODE, sizeof ( uint8 ), &pairMode );

     GAPBondMgr_SetParameter( GAPBOND_MITM_PROTECTION, sizeof ( uint8 ), &mitm );

     GAPBondMgr_SetParameter( GAPBOND_IO_CAPABILITIES, sizeof ( uint8 ), &ioCap );

     GAPBondMgr_SetParameter( GAPBOND_BONDING_ENABLED, sizeof ( uint8 ), &bonding );

   }

   // Initialize GATT attributes

   GGS_AddService( GATT_ALL_SERVICES );            // GAP

   GATTServApp_AddService( GATT_ALL_SERVICES );    // GATT attributes

   DevInfo_AddService();                           // Device Information Service

   SimpleProfile_AddService( GATT_ALL_SERVICES );  // Simple GATT Profile

 #if defined FEATURE_OAD

   VOID OADTarget_AddService();                    // OAD Profile

 #endif

   // Setup the SimpleProfile Characteristic Values

   {

     uint8 charValue1 = ;

     uint8 charValue2 = ;

     uint8 charValue3 = ;

     uint8 charValue4 = ;

     uint8 charValue5[SIMPLEPROFILE_CHAR5_LEN] = { , , , ,  };

     SimpleProfile_SetParameter( SIMPLEPROFILE_CHAR1, sizeof ( uint8 ), &charValue1 );

     SimpleProfile_SetParameter( SIMPLEPROFILE_CHAR2, sizeof ( uint8 ), &charValue2 );

     SimpleProfile_SetParameter( SIMPLEPROFILE_CHAR3, sizeof ( uint8 ), &charValue3 );

     SimpleProfile_SetParameter( SIMPLEPROFILE_CHAR4, sizeof ( uint8 ), &charValue4 );

     SimpleProfile_SetParameter( SIMPLEPROFILE_CHAR5, SIMPLEPROFILE_CHAR5_LEN, charValue5 );

   }

 #if defined( CC2540_MINIDK )

   SK_AddService( GATT_ALL_SERVICES ); // Simple Keys Profile

   // Register for all key events - This app will handle all key events

   RegisterForKeys( simpleBLEPeripheral_TaskID );

   // makes sure LEDs are off

   HalLedSet( (HAL_LED_1 | HAL_LED_2), HAL_LED_MODE_OFF );

   // For keyfob board set GPIO pins into a power-optimized state

   // Note that there is still some leakage current from the buzzer,

   // accelerometer, LEDs, and buttons on the PCB.

   P0SEL = ; // Configure Port 0 as GPIO

   P1SEL = ; // Configure Port 1 as GPIO

   P2SEL = ; // Configure Port 2 as GPIO

   P0DIR = 0xFC; // Port 0 pins P0.0 and P0.1 as input (buttons),

                 // all others (P0.2-P0.7) as output

   P1DIR = 0xFF; // All port 1 pins (P1.0-P1.7) as output

   P2DIR = 0x1F; // All port 1 pins (P2.0-P2.4) as output

   P0 = 0x03; // All pins on port 0 to low except for P0.0 and P0.1 (buttons)

   P1 = ;   // All pins on port 1 to low

   P2 = ;   // All pins on port 2 to low

 #else

   // Register for all key events - This app will handle all key events

   RegisterForKeys( simpleBLEPeripheral_TaskID );

 #endif // #if defined( CC2540_MINIDK )

 #if (defined HAL_LCD) && (HAL_LCD == TRUE)

 #if defined FEATURE_OAD

   #if defined (HAL_IMAGE_A)

     HalLcdWriteStringValue( "BLE Peri-A", OAD_VER_NUM( _imgHdr.ver ), , HAL_LCD_LINE_1 );

   #else

     HalLcdWriteStringValue( "BLE Peri-B", OAD_VER_NUM( _imgHdr.ver ), , HAL_LCD_LINE_1 );

   #endif // HAL_IMAGE_A

 #else

   HalLcdWriteString( "BLE Peripheral", HAL_LCD_LINE_1 );

 #endif // FEATURE_OAD

 #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

   // Register callback with SimpleGATTprofile

   VOID SimpleProfile_RegisterAppCBs( &simpleBLEPeripheral_SimpleProfileCBs );

   // Enable clock divide on halt

   // This reduces active current while radio is active and CC254x MCU

   // is halted

   HCI_EXT_ClkDivOnHaltCmd( HCI_EXT_ENABLE_CLK_DIVIDE_ON_HALT );

 #if defined ( DC_DC_P0_7 )

   // Enable stack to toggle bypass control on TPS62730 (DC/DC converter)

   HCI_EXT_MapPmIoPortCmd( HCI_EXT_PM_IO_PORT_P0, HCI_EXT_PM_IO_PORT_PIN7 );

 #endif // defined ( DC_DC_P0_7 )

   // Setup a delayed profile startup

   osal_set_event( simpleBLEPeripheral_TaskID, SBP_START_DEVICE_EVT );

 }

 /*********************************************************************

  * @fn      SimpleBLEPeripheral_ProcessEvent

  *

  * @brief   Simple BLE Peripheral Application Task event processor.  This function

  *          is called to process all events for the task.  Events

  *          include timers, messages and any other user defined events.

  *

  * @param   task_id  - The OSAL assigned task ID.

  * @param   events - events to process.  This is a bit map and can

  *                   contain more than one event.

  *

  * @return  events not processed

  */

 uint16 SimpleBLEPeripheral_ProcessEvent( uint8 task_id, uint16 events )

 {

   VOID task_id; // OSAL required parameter that isn't used in this function

   if ( events & SYS_EVENT_MSG )

   {

     uint8 *pMsg;

     if ( (pMsg = osal_msg_receive( simpleBLEPeripheral_TaskID )) != NULL )

     {

       simpleBLEPeripheral_ProcessOSALMsg( (osal_event_hdr_t *)pMsg );

       // Release the OSAL message

       VOID osal_msg_deallocate( pMsg );

     }

     // return unprocessed events

     return (events ^ SYS_EVENT_MSG);

   }

   if ( events & SBP_START_DEVICE_EVT )

   {

     // Start the Device

     VOID GAPRole_StartDevice( &simpleBLEPeripheral_PeripheralCBs );

     // Start Bond Manager

     VOID GAPBondMgr_Register( &simpleBLEPeripheral_BondMgrCBs );

     // Set timer for first periodic event

     osal_start_timerEx( simpleBLEPeripheral_TaskID, SBP_PERIODIC_EVT, SBP_PERIODIC_EVT_PERIOD );

     return ( events ^ SBP_START_DEVICE_EVT );

   }

   if ( events & SBP_PERIODIC_EVT )

   {

     // Restart timer

     if ( SBP_PERIODIC_EVT_PERIOD )

     {

       osal_start_timerEx( simpleBLEPeripheral_TaskID, SBP_PERIODIC_EVT, SBP_PERIODIC_EVT_PERIOD );

     }

     // Perform periodic application task

     // performPeriodicTask();

     return (events ^ SBP_PERIODIC_EVT);

   }

 #if defined ( PLUS_BROADCASTER )

   if ( events & SBP_ADV_IN_CONNECTION_EVT )

   {

     uint8 turnOnAdv = TRUE;

     // Turn on advertising while in a connection

     GAPRole_SetParameter( GAPROLE_ADVERT_ENABLED, sizeof( uint8 ), &turnOnAdv );

     return (events ^ SBP_ADV_IN_CONNECTION_EVT);

   }

 #endif // PLUS_BROADCASTER

   // Discard unknown events

   return ;

 }

 /*********************************************************************

  * @fn      simpleBLEPeripheral_ProcessOSALMsg

  *

  * @brief   Process an incoming task message.

  *

  * @param   pMsg - message to process

  *

  * @return  none

  */

 static void simpleBLEPeripheral_ProcessOSALMsg( osal_event_hdr_t *pMsg )

 {

   switch ( pMsg->event )

   {

   //#if defined( CC2540_MINIDK )

     case KEY_CHANGE:

       simpleBLEPeripheral_HandleKeys( ((keyChange_t *)pMsg)->state, ((keyChange_t *)pMsg)->keys );

       break;

   //#endif // #if defined( CC2540_MINIDK )

   default:

     // do nothing

     break;

   }

 }

 //#if defined( CC2540_MINIDK )

 /*********************************************************************

  * @fn      simpleBLEPeripheral_HandleKeys

  *

  * @brief   Handles all key events for this device.

  *

  * @param   shift - true if in shift/alt.

  * @param   keys - bit field for key events. Valid entries:

  *                 HAL_KEY_SW_2

  *                 HAL_KEY_SW_1

  *

  * @return  none

  */

 uint8 gTxPower = LL_EXT_TX_POWER_4_DBM;

 static void simpleBLEPeripheral_HandleKeys( uint8 shift, uint8 keys )

 {

   (void)shift;  // Intentionally unreferenced parameter

   HalLcdWriteStringValue( "key = 0x", keys, , HAL_LCD_LINE_4 );

   // smartRF开发板上的S1 对应我们源码上的HAL_KEY_SW_6

   if ( keys & HAL_KEY_SW_6 )

   {

     HalLcdWriteString( "HAL_KEY_SW_6", HAL_LCD_LINE_5 );

   }

   if ( keys & HAL_KEY_UP )

   {

     HalLcdWriteString( "HAL_KEY_UP", HAL_LCD_LINE_5 );

     /*

 #define LL_EXT_TX_POWER_MINUS_23_DBM                   0 // -23dbm  功率 最小

 #define LL_EXT_TX_POWER_MINUS_6_DBM                    1 // -6dbm

 #define LL_EXT_TX_POWER_0_DBM                          2  // 0dbm

 #define LL_EXT_TX_POWER_4_DBM                          3  // +dbm  功率 最大

     */

     if(gTxPower < LL_EXT_TX_POWER_4_DBM)

     {

         gTxPower++;   //功率提高一档

         HCI_EXT_SetTxPowerCmd(gTxPower);

         HalLcdWriteStringValue( "TxPower: ", gTxPower, , HAL_LCD_LINE_7 );

     }

   }

   if ( keys & HAL_KEY_LEFT )

   {

     HalLcdWriteString( "HAL_KEY_LEFT", HAL_LCD_LINE_5 );

   }

   if ( keys & HAL_KEY_RIGHT )

   {

     HalLcdWriteString( "HAL_KEY_RIGHT", HAL_LCD_LINE_5 );

   }

   if ( keys & HAL_KEY_CENTER )

   {

     HalLcdWriteString( "HAL_KEY_CENTER", HAL_LCD_LINE_5 );

   }

   if ( keys & HAL_KEY_DOWN )

   {

     HalLcdWriteString( "HAL_KEY_DOWN", HAL_LCD_LINE_5 );

     /*

 #define LL_EXT_TX_POWER_MINUS_23_DBM                   0 // -23dbm  功率 最小

 #define LL_EXT_TX_POWER_MINUS_6_DBM                    1 // -6dbm

 #define LL_EXT_TX_POWER_0_DBM                          2  // 0dbm

 #define LL_EXT_TX_POWER_4_DBM                          3  // +dbm  功率 最大

     */

     if(gTxPower > LL_EXT_TX_POWER_MINUS_23_DBM)

     {

         gTxPower--; //功率降低一档

         HCI_EXT_SetTxPowerCmd(gTxPower);

         HalLcdWriteStringValue( "TxPower: ", gTxPower, , HAL_LCD_LINE_7 );

     }

   }

 }

 //#endif // #if defined( CC2540_MINIDK )

 /*********************************************************************

  * @fn      peripheralStateNotificationCB

  *

  * @brief   Notification from the profile of a state change.

  *

  * @param   newState - new state

  *

  * @return  none

  */

 static void peripheralStateNotificationCB( gaprole_States_t newState )

 {

   switch ( newState )

   {

     case GAPROLE_STARTED:

       {

         uint8 ownAddress[B_ADDR_LEN];

         uint8 systemId[DEVINFO_SYSTEM_ID_LEN];

         GAPRole_GetParameter(GAPROLE_BD_ADDR, ownAddress);

         // use 6 bytes of device address for 8 bytes of system ID value

         systemId[] = ownAddress[];

         systemId[] = ownAddress[];

         systemId[] = ownAddress[];

         // set middle bytes to zero

         systemId[] = 0x00;

         systemId[] = 0x00;

         // shift three bytes up

         systemId[] = ownAddress[];

         systemId[] = ownAddress[];

         systemId[] = ownAddress[];

         DevInfo_SetParameter(DEVINFO_SYSTEM_ID, DEVINFO_SYSTEM_ID_LEN, systemId);

         #if (defined HAL_LCD) && (HAL_LCD == TRUE)

           // Display device address

           HalLcdWriteString( bdAddr2Str( ownAddress ),  HAL_LCD_LINE_2 );

           HalLcdWriteString( "Initialized",  HAL_LCD_LINE_3 );

         #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

       }

       break;

     case GAPROLE_ADVERTISING:

       {

         #if (defined HAL_LCD) && (HAL_LCD == TRUE)

           HalLcdWriteString( "Advertising",  HAL_LCD_LINE_3 );

         #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

       }

       break;

     case GAPROLE_CONNECTED:

       {

         #if (defined HAL_LCD) && (HAL_LCD == TRUE)

             HalLcdWriteString( "Connected",  HAL_LCD_LINE_3 );

             HCI_EXT_SetTxPowerCmd(gTxPower);

         #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

       }

       break;

     case GAPROLE_WAITING:

       {

         #if (defined HAL_LCD) && (HAL_LCD == TRUE)

           HalLcdWriteString( "Disconnected",  HAL_LCD_LINE_3 );

         #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

       }

       break;

     case GAPROLE_WAITING_AFTER_TIMEOUT:

       {

         #if (defined HAL_LCD) && (HAL_LCD == TRUE)

           HalLcdWriteString( "Timed Out",  HAL_LCD_LINE_3 );

         #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

       }

       break;

     case GAPROLE_ERROR:

       {

         #if (defined HAL_LCD) && (HAL_LCD == TRUE)

           HalLcdWriteString( "Error",  HAL_LCD_LINE_3 );

         #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

       }

       break;

     default:

       {

         #if (defined HAL_LCD) && (HAL_LCD == TRUE)

           HalLcdWriteString( "",  HAL_LCD_LINE_3 );

         #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

       }

       break;

   }

   gapProfileState = newState;

 #if !defined( CC2540_MINIDK )

   VOID gapProfileState;     // added to prevent compiler warning with

                             // "CC2540 Slave" configurations

 #endif

 }

 /*********************************************************************

  * @fn      performPeriodicTask

  *

  * @brief   Perform a periodic application task. This function gets

  *          called every five seconds as a result of the SBP_PERIODIC_EVT

  *          OSAL event. In this example, the value of the third

  *          characteristic in the SimpleGATTProfile service is retrieved

  *          from the profile, and then copied into the value of the

  *          the fourth characteristic.

  *

  * @param   none

  *

  * @return  none

  */

 static void performPeriodicTask( void )

 {

   uint8 valueToCopy;

   uint8 stat;

   // Call to retrieve the value of the third characteristic in the profile

   stat = SimpleProfile_GetParameter( SIMPLEPROFILE_CHAR3, &valueToCopy);

   if( stat == SUCCESS )

   {

     /*

      * Call to set that value of the fourth characteristic in the profile. Note

      * that if notifications of the fourth characteristic have been enabled by

      * a GATT client device, then a notification will be sent every time this

      * function is called.

      */

     SimpleProfile_SetParameter( SIMPLEPROFILE_CHAR4, sizeof(uint8), &valueToCopy);

   }

 }

 /*********************************************************************

  * @fn      simpleProfileChangeCB

  *

  * @brief   Callback from SimpleBLEProfile indicating a value change

  *

  * @param   paramID - parameter ID of the value that was changed.

  *

  * @return  none

  */

 static void simpleProfileChangeCB( uint8 paramID )

 {

   uint8 newValue;

   switch( paramID )

   {

     case SIMPLEPROFILE_CHAR1:

       SimpleProfile_GetParameter( SIMPLEPROFILE_CHAR1, &newValue );

       #if (defined HAL_LCD) && (HAL_LCD == TRUE)

         HalLcdWriteStringValue( "Char 1:", (uint16)(newValue), ,  HAL_LCD_LINE_3 );

       #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

       break;

     case SIMPLEPROFILE_CHAR3:

       SimpleProfile_GetParameter( SIMPLEPROFILE_CHAR3, &newValue );

       #if (defined HAL_LCD) && (HAL_LCD == TRUE)

         HalLcdWriteStringValue( "Char 3:", (uint16)(newValue), ,  HAL_LCD_LINE_3 );

       #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

       break;

     default:

       // should not reach here!

       break;

   }

 }

 #if (defined HAL_LCD) && (HAL_LCD == TRUE)

 /*********************************************************************

  * @fn      bdAddr2Str

  *

  * @brief   Convert Bluetooth address to string. Only needed when

  *          LCD display is used.

  *

  * @return  none

  */

 char *bdAddr2Str( uint8 *pAddr )

 {

   uint8       i;

   char        hex[] = "0123456789ABCDEF";

   static char str[B_ADDR_STR_LEN];

   char        *pStr = str;

   *pStr++ = '';

   *pStr++ = 'x';

   // Start from end of addr

   pAddr += B_ADDR_LEN;

   for ( i = B_ADDR_LEN; i > ; i-- )

   {

     *pStr++ = hex[*--pAddr >> ];

     *pStr++ = hex[*pAddr & 0x0F];

   }

   *pStr = ;

   return str;

 }

 #endif // (defined HAL_LCD) && (HAL_LCD == TRUE)

 /*********************************************************************

 *********************************************************************/

>>更好的方式应该是寻找默认广播发送功率的原始设置方式

相关链接：

2、利用蓝牙定位及姿态识别实现一个智能篮球场套件（二）——CC2540/CC2541基于广播的RSSI获得
1、利用蓝牙定位及姿态识别实现一个智能篮球场套件（一）——用重写CC2541透传模块做成智能手环
5、CC2541芯片中级教程-OSAL操作系统（PWM+看门狗）
4、CC2541芯片中级教程-OSAL操作系统（简单AT指令实现+IIC软件和硬件实现驱动MPU6050）
3、CC2541芯片中级教程-OSAL操作系统（ADC光敏电阻和修改串口波特率）
2、CC2541芯片中级教程-OSAL操作系统（进一步了解-OLED && 普通按键和5方向按键-中断！！！）这个系统驱动层和应用层不一样~
1、CC2541蓝牙4.0芯片中级教程——基于OSAL操作系统的运行流程了解+定时器和串口例程了解

:: 如果您觉得不错，请推荐给更多人，帮助他们更快地解决实际问题中的坑~

@beautifulzzzz

智能硬件、物联网，热爱技术，关注产品

博客：http://blog.beautifulzzzz.com

园友交流群：414948975