工程坐标转换方法C#代码实现

时间:2022-12-04 21:05:55

前面的文章中系统的阐述了工程坐标的转换类别和转换的方法。关于转换代码实现,有很多的类库:

这里针对GPS接收的WGS84椭球的经纬度转换为地方坐标系的问题,利用C#,对工程坐标转换方法和步骤做出详细的解答。不基于任何类库和函数库,也未使用矩阵库,可以便利的将代码移植到任何语言。


2. 计算总体框架

根据上一篇文章中对七参数、四参数、高程拟合在坐标转换的作用和使用条件的阐述,我们可以将上一篇文章第7节的总结图,按照计算的流程重新绘制。
工程坐标转换方法C#代码实现

根据上图可知,预将WGS84椭球的GPS坐标需要经过5次转换。其中,

  1. 转换1、转换3在charlee44的博客:大地经纬度坐标与地心地固坐标的转换中详细讲解了,并且有C++代码的实现,利用C#重构即可。
  2. 转换2、转换5,以及他们的组合,在我的上一篇文章(工程)坐标转换类别和方法也详细的讲解了。

因此,根据计算原理,直接可以利用C#代码实现。


3. C#代码实现

3.1 整体类的构建

5个转换是对点的操作,不妨构建自定义点类MyPoint,在这个类中定义转换方法。在实现转换方法之前,需要定义数据属性,以承载转换参数和转换数据。代码框架如下:

internal class MyPoint
{
	// 定义椭球类型。这里仅列举了4中国内常见的椭球类型
	// 国际椭球可以增加自行定义	
	public enum EllipsoidType
	     {
	         WGS84,
	         CGCS2000,
	         西安80,
	         北京54
	     }
	    //大地坐标经度、维度、高度
	    public double L { get; set; }
	    public double B { get; set; }
	    public double H { get; set; }
	
	    //空间坐标系
	    public double X { get; set; }
	    public double Y { get; set; }
	    public double Z { get; set; }
	
	    //七参数转换后的空间坐标
	    public double X2 { get; set; }
	    public double Y2 { get; set; }
	    public double Z2 { get; set; }
	
	    
	    
	    private double a = 0, f = 0, b = 0, e = 0, e2 = 0;    //椭球参数
	
	    private readonly double rho = 180 / Math.PI;
	    private readonly double d2r = Math.PI / 180;
	
	    public double Xs { get; set; }
	    public double Ys { get; set; }
	    public double Hs { get; set; }
	
	    //七参数 三个线性平移量-单位米 三个旋转平移量-十进制秒为单位(运算时注意转换为度) 比例因子-单位百万分率 (ppm)
	    //测量队给出的七参数单位与计算的单位不同,要进行单位转化 1 秒=0.0000048481373323 弧度
	    //尺度因子有两种单位的表示形式,一种结果约为1,如1.0000045,用k表示;
	    //另一种就是ppm的表示形式,稍微比1大一点,如4.5,用m表示。k=m/1000000
	    private double dx = 0, dy = 0, dz = 0, rx = 0, ry = 0, rz = 0, m = 0, k = 0;    
}

3.2 椭球参数赋值

常见的椭球参数值在我的文章经纬度坐标转换为工程坐标可以找到,这里选取与上述代码对应的4类椭球,并在上述MyPoint类中增加函数EllipsoidParam(EllipsoidType type)

/// <summary>
/// 椭球参数设置
/// </summary>
/// <param name="type">椭球类型</param>
private void EllipsoidParam(EllipsoidType type)
{
    // CGCS2000 椭球参数
    if (type == EllipsoidType.CGCS2000)
    {
        this.a = 6378137;
        this.f = 1 / 298.257222101;
    }

    // 西安 80
    else if (type == EllipsoidType.西安80)
    {
        this.a = 6378140;
        this.f = 1 / 298.257;
    }

    // 北京 54
    else if (type == EllipsoidType.北京54)
    {
        this.a = 6378245;
        this.f = 1 / 298.3;
    }

    // WGS-84 
    else
    {
        this.a = 6378137;
        this.f = 1 / 298.257223563;
    }

    this.b = this.a * (1 - this.f);
    this.e = Math.Sqrt(this.a * this.a - this.b * this.b) / this.a;  //第一偏心率
    this.e2 = Math.Sqrt(this.a * this.a - this.b * this.b) / this.b;  //第二偏心率
}

3.3 转换1、3(大地经纬度坐标与地心地固坐标的转换)

charlee44的博客有C++代码的实现,现在利用C#重构即可。上述MyPoint类中增加BLH2XYZ(EllipsoidType type)XYZ2BLH(EllipsoidType type)两个函数

/// <summary>
/// 经纬度坐标转空间直角坐标
/// </summary>
/// <param name="type">椭球类型</param>
public void BLH2XYZ(EllipsoidType type = EllipsoidType.WGS84)
{
    EllipsoidParam(type);

    double sB = Math.Sin(this.B * d2r);
    double cB = Math.Cos(this.B * d2r);
    double sL = Math.Sin(this.L * d2r);
    double cL = Math.Cos(this.L * d2r);
    double N = this.a / (Math.Sqrt(1 - this.e * this.e * sB * sB));

    this.X = (N + this.H) * cB * cL;
    this.Y = (N + this.H) * cB * sL;
    this.Z = (N * (1 - this.e * this.e) + this.H) * sB;

    this.X2 = this.X;
    this.Y2 = this.Y;
    this.Z2 = this.Z;
}

/// <summary>
/// 空间直角坐标转经纬度坐标
/// </summary>
/// <param name="type">椭球类型</param>
public void XYZ2BLH(EllipsoidType type)
{
    EllipsoidParam(type);

    // 这里转出来的B L是弧度
    this.L = Math.Atan(this.Y2 / this.X2) + Math.PI;
    
    this.L = this.L * 180 / Math.PI;
    // B需要迭代计算
    double B2 = Math.Atan(Z2 / Math.Sqrt(X2 * X2 + Y2 * Y2));
    double B1;
    double N;
    while (true)
    {
        N = a / Math.Sqrt(1 - f * (2 - f) * Math.Sin(B2) * Math.Sin(B2));
        B1 = Math.Atan((Z2 + N * f * (2 - f) * Math.Sin(B2)) / Math.Sqrt(X2 * X2 + Y2 * Y2));
        if (Math.Abs(B1 - B2) < 1e-12)
            break;
        B2 = B1;
    }
    this.B = B2 * 180 / Math.PI;
    double sB = Math.Sin(this.B * d2r);
    double cB = Math.Cos(this.B * d2r);
    this.H = this.Z2 / sB - N * (1 - this.e * this.e);
}

3.4 投影转换

此处仅实现了常见的高斯-克里格投影。上述MyPoint类中增加GaussProjection(EllipsoidType type, ProjectionSetting prjSetting)函数

/// <summary>
/// 利用高斯投影将指定椭球类型的经纬度坐标转为投影坐标
/// </summary>
/// <param name="type">椭球类型</param>
/// <param name="prjSetting">投影设置实例</param>
public void GaussProjection(EllipsoidType type, ProjectionSetting prjSetting)
{
    this.EllipsoidParam(type);

    double l = (this.L - prjSetting.CenterL) / this.rho;

    double cB = Math.Cos(this.B * this.d2r);
    double sB = Math.Sin(this.B * this.d2r);
    double s2b = Math.Sin(this.B * this.d2r * 2);
    double s4b = Math.Sin(this.B * this.d2r * 4);
    double s6b = Math.Sin(this.B * this.d2r * 6);
    double s8b = Math.Sin(this.B * this.d2r * 8);

    double N = this.a / Math.Sqrt(1 - this.e * this.e * sB * sB);       // 卯酉圈曲率半径
    double t = Math.Tan(this.B * this.d2r);
    double eta = this.e2 * cB;

    double m0 = this.a * (1 - this.e * this.e);
    double m2 = 3.0 / 2.0 * this.e * this.e * m0;
    double m4 = 5.0 / 4.0 * this.e * this.e * m2;
    double m6 = 7.0 / 6.0 * this.e * this.e * m4;
    double m8 = 9.0 / 8.0 * this.e * this.e * m6;

    double a0 = m0 + 1.0 / 2.0 * m2 + 3.0 / 8.0 * m4 + 5.0 / 16.0 * m6 + 35.0 / 128.0 * m8;
    double a2 = 1.0 / 2.0 * m2 + 1.0 / 2.0 * m4 + 15.0 / 32.0 * m6 + 7.0 / 16.0 * m8;
    double a4 = 1.0 / 8.0 * m4 + 3.0 / 16.0 * m6 + 7.0 / 32.0 * m8;
    double a6 = 1.0 / 32.0 * m6 + 1.0 / 16.0 * m8;
    double a8 = 1.0 / 128.0 * m8;

    // X1为自赤道量起的子午线弧长
    double X1 = a0 * (this.B * this.d2r) - 1.0 / 2.0 * a2 * s2b + 1.0 / 4.0 * a4 * s4b - 1.0 / 6.0 * a6 * s6b + 1.0 / 8.0 * a8 * s8b;

    this.Xs = X1 + N / 2 * t * cB * cB * l * l + N / 24 * t * (5 - t * t + 9 * Math.Pow(eta, 2) + 4 * Math.Pow(eta, 4)) * Math.Pow(cB, 4) * Math.Pow(l, 4)
          + N / 720 * t * (61 - 58 * t * t + Math.Pow(t, 4)) * Math.Pow(cB, 6) * Math.Pow(l, 6);

    
    this.Ys = N * cB * l + N / 6 * (1 - t * t + eta * eta) * Math.Pow(cB, 3) * Math.Pow(l, 3)
        + N / 120 * (5 - 18 * t * t + Math.Pow(t, 4) + 14 * Math.Pow(eta, 2) - 58 * eta * eta * t * t) * Math.Pow(cB, 5) * Math.Pow(l, 5);

    this.Hs = this.H;

    // 假东 假北偏移
    
    this.Xs += prjSetting.PseudoNorth;
    this.Ys += prjSetting.PseudoEast;
}

其中,ProjectionSetting是一个投影参数设置类,独立于MyPoint,用于设定*经线、东偏等投影参数

internal class ProjectionSetting
    {
		private double _centerL;

		public double CenterL
		{
			get { return _centerL; }
			set { _centerL = value; }
		}

		private double _centerB;

		public double CenterB
		{
			get { return _centerB; }
			set { _centerB = value; }
		}

		private double _pseudoEast;

		public double PseudoEast
        {
			get { return _pseudoEast; }
			set { _pseudoEast = value; }
		}

		private double _pseudoNorth;

		public double PseudoNorth
        {
			get { return _pseudoNorth; }
			set { _pseudoNorth = value; }
		}

		private double _prjScale;

		public double PrjScale
		{
			get { return _prjScale; }
			set { _prjScale = value; }
		}

		/// <summary>
		/// 设置全部的投影参数
		/// </summary>
		/// <param name="centerL"></param>
		/// <param name="centerB"></param>
		/// <param name="pseudoEast"></param>
		/// <param name="pseudoNorth"></param>
		/// <param name="prjScale"></param>
		public ProjectionSetting(double centerL, double centerB, 
			double pseudoEast, double pseudoNorth,
			double prjScale)
		{
			CenterL = centerL;
			CenterB = centerB;
			PseudoEast = pseudoEast;
			PseudoNorth = pseudoNorth;
			PrjScale = prjScale;
		}

		/// <summary>
		/// 仅设置*经线和东偏
		/// </summary>
		/// <param name="centerL"></param>
		/// <param name="pseudoEast"></param>
		public ProjectionSetting(double centerL, double pseudoEast)
		{
            CenterL = centerL;
            CenterB = 0.0;
            PseudoEast = pseudoEast;
            PseudoNorth = 0.0;
            PrjScale = 1.0;
        }

		/// <summary>
		/// 默认常用投影参数,*经线120°,东偏500000
		/// </summary>
		public ProjectionSetting()
		{
            CenterL = 120.0;
            CenterB = 0.0;
            PseudoEast = 500000;
            PseudoNorth = 0.0;
            PrjScale = 1.0;
        }
	}

3.5 转换2的实现(三参数、七参数)

上述MyPoint类中增加SevenParamTrans(Datum7Paras datum7Paras)TreeParamTrans(Datum3Paras datum3Paras)函数

/// <summary>
/// 利用7参数进行坐标系之间转换
/// </summary>
/// <param name="datum7Paras">7参数实例</param>
public void SevenParamTrans(Datum7Paras datum7Paras)
{
    this.dx = datum7Paras.Dx;
    this.dy = datum7Paras.Dy;
    this.dz = datum7Paras.Dz;
    this.rx = datum7Paras.Rx * 0.0000048481373323; //1 秒=0.0000048481373323 弧度
    this.ry = datum7Paras.Ry * 0.0000048481373323;
    this.rz = datum7Paras.Rz * 0.0000048481373323;
    this.m = datum7Paras.PPM;
    this.k = this.m / 1000000;

    this.X2 = (1 + k) * (this.X + this.rz * this.Y - this.ry * this.Z) + this.dx;
    this.Y2 = (1 + k) * (-this.rz * this.X + this.Y + this.rx * this.Z) + this.dy;
    this.Z2 = (1 + k) * (this.ry * this.X - this.rx * this.Y + this.Z) + this.dz;
}

/// <summary>
/// 利用3参数进行坐标系之间转换
/// </summary>
/// <param name="datum3Paras">3参数实例</param>
public void TreeParamTrans(Datum3Paras datum3Paras)
{
    this.dx = datum3Paras.Dx;
    this.dy = datum3Paras.Dy;
    this.dz = datum3Paras.Dz;

    this.X2 = this.X + this.dx;
    this.Y2 = this.Y + this.dy;
    this.Z2 = this.Z + this.dz;
}

Datum3ParasDatum7Paras独立于MyPoint,用于设定坐标转换参数

   /// <summary>
    /// 7参数
    /// </summary>
    internal class Datum7Paras
    {
		private double _dx;

		public double Dx
		{
			get { return _dx; }
			set { _dx = value; }
		}

        private double _dy;

        public double Dy
        {
            get { return _dy; }
            set { _dy = value; }
        }

        private double _dz;

        public double Dz
        {
            get { return _dz; }
            set { _dz = value; }
        }


        private double _rx;

        public double Rx
        {
            get { return _rx; }
            set { _rx = value; }
        }

        private double _ry;

        public double Ry
        {
            get { return _ry; }
            set { _ry = value; }
        }


        private double _rz;

        public double Rz
        {
            get { return _rz; }
            set { _rz = value; }
        }

        private double _ppm;

        public double PPM
        {
            get { return _ppm; }
            set { _ppm = value; }
        }

        public Datum7Paras(double dx, double dy,  double dz,  
            double rx,  double ry,  double rz, 
            double ppm)
        {
            _dx = dx;
            _dy = dy;
            _dz = dz;

            _rx = rx;
            _ry = ry;
            _rz = rz;

            _ppm = ppm;
        }
    }
    internal class Datum3Paras
    {
        private double _dx;

        public double Dx
        {
            get { return _dx; }
            set { _dx = value; }
        }

        private double _dy;

        public double Dy
        {
            get { return _dy; }
            set { _dy = value; }
        }

        private double _dz;

        public double Dz
        {
            get { return _dz; }
            set { _dz = value; }
        }


        public Datum3Paras(double dx,  double dy,  double dz)
        {
            Dx = dx;
            Dy = dy;
            Dz = dz;
        }
    }

3.6 转换5的实现(四参数+高程拟合)

上述MyPoint类中增加Transform4Para(Trans4Paras transPara)函数。此处,高程拟合仅实现了已知一个测点的固定改正差

/// <summary>
/// 投影坐标获取后,进一步利用4参数转换坐标
/// </summary>
/// <param name="transPara"></param>
public void Transform4Para(Trans4Paras transPara)
{
    var X1 = transPara.Dx;
    var Y1 = transPara.Dy;

    var cosAngle = Math.Cos(transPara.A);
    var sinAngle = Math.Sin(transPara.A);

    X1 += transPara.K * (cosAngle * this.Xs - sinAngle * this.Ys);
    Y1 += transPara.K * (sinAngle * this.Xs + cosAngle * this.Ys);

    this.Xs = X1;
    this.Ys = Y1;
	// 固定改正差
    this.Hs += transPara.Dh;
}

Trans4Paras独立于MyPoint,用于设定坐标转换参数

    internal class Trans4Paras
    {
        private double _dx;

        public double Dx
        {
            get { return _dx; }
            set { _dx = value; }
        }

        private double _dy;

        public double Dy
        {
            get { return _dy; }
            set { _dy = value; }
        }

        private double _a;

        public double A
        {
            get { return _a; }
            set { _a = value; }
        }

        private double _k;

        public double K
        {
            get { return _k; }
            set { _k = value; }
        }

        private double _dh;

        public double Dh
        {
            get { return _dh; }
            set { _dh = value; }
        }

        
        public Trans4Paras(double dx, double dy, double a, double k, double dh)
        {
            Dx = dx;
            Dy = dy;
            A = a;
            K = k;
            Dh = dh;
        }

        public Trans4Paras()
        {
        }
    }

3.7 调用过程

里面的参数,因为保密原因,做出了随机更改,实际使用时可根据自己情况赋值。

3.7.1 一步法

// 实例化计算参数
MyPoint p = new MyPoint();.

p.L=113.256;
p.B=31.565;
p.H=5.216;
 
// 经纬度转空间坐标
p.BLH2XYZ();

// 实例化七参数
Datum7Paras datum7Paras = new Datum7Paras(
    489.2994563566, 141.1525159753, 15.74421120568,
    -0.164423, 4.141573, -4.808299,
    -6.56482989958);

p.SevenParamTrans(datum7Paras);

// 空间坐标转回经纬度
p.XYZ2BLH(EllipsoidType.WGS84);

// 高斯投影 经纬度转平面坐标
// 实例化投影参数类
ProjectionSetting projectionSetting = new ProjectionSetting(120,500000);
p.GaussProjection(EllipsoidType.WGS84, projectionSetting);

3.7.2 两步法

// 实例化计算参数
MyPoint p = new MyPoint();.

p.SetLBH(113.256,31.565,5.216);
 
// 经纬度转空间坐标
p.BLH2XYZ();

// 实例化七参数
Datum7Paras datum7Paras = new Datum7Paras(
    489.2994563566, 141.1525159753, 15.74421120568,
    -0.164423, 4.141573, -4.808299,
    -6.56482989958);

p.SevenParamTrans(datum7Paras);

// 空间坐标转回经纬度
p.XYZ2BLH(EllipsoidType.WGS84);

// 高斯投影 经纬度转平面坐标
// 实例化投影参数类
ProjectionSetting projectionSetting = new ProjectionSetting(120,500000);
p.GaussProjection(EllipsoidType.WGS84, projectionSetting);

Trans4Paras transformPara = new(6456.15957352521, -134618.390707439, 0.011104964500129, 1.00002537583871, 5.788);

p.Transform4Para(transformPara);


4. 总结

至此,关于工程坐标系转化,即GPS接收的WGS84椭球的经纬度转换为地方坐标系的问题,基本全部实现。代码正确性和准确性的验证是与 南方GPS工具箱做对比。例如,采用上述的一步法,在设定好坐标、7参数、投影参数后,计算发现,与南方GPS工具箱在y方向偏差1mm。结果如下图:
工程坐标转换方法C#代码实现