Gentoo 无线网络配置 wpa_supplicant

时间：2023-06-11 21:53:36
Gentoo 无线网络配置 wpa_supplicant

安装

安装net-wireless/wpa_supplicant包

emerge --ask wpa_supplicant

启动网络

  • 为wpa_supplicant添加无线接口

    在wpa_supplicant.conf文件中添加
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel
  • 初始化wpa_supplicant环境
wpa_supplicant -d -Dnl80211 -iwlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf

参数：

-B - Fork into background.

-c filename - Path to configuration file.

-d increase debugging verbosity

-i interface - Interface to listen on.

-D driver - Optionally specify the driver to be used.

For a list of supported drivers see the output of wpa_supplicant -h.

nl80211 is the current standard, but not all wireless chip's modules support it.wext is currently deprecated, but still widely supported.

  • 查看wpa_supplicant进程
ps -aux | grep wpa

root      1841  0.0  0.2   6168  2920 ?        Ss   09:10   0:00 wpa_supplicant -B -c/etc/wpa_supplicant/wpa_supplicant.conf -iwlan0

root      2122  0.0  0.0   2780   728 pts/0    S+   09:25   0:00 grep --colour=auto wpa

配置

  • Set for Gentoo net.* scrips，tell the network script to use wpa_supplicant.

    File/etc/conf.d/net 
modules_wlan0="wpa_supplicant"

# 因为wpa_supplicant还不能很好的自动侦测驱动，所以需要我们为其指定正在使用的驱动。

wpa_supplicant_wlan0="-Dnl80211"

config_wlan0="dhcp"
  • Set for dhcpcd,no special setup is needed.Do not add wpa_supplicant to any runlevel. It will be controlled by dhcpcd.

配置文件/etc/wpa_supplicant/wpa_supplicant.conf

# Allow users in the 'wheel' group to control wpa_supplicant

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel

# Make this file writable for wpa_gui

update_config=1

#自动扫描AP（也就是可以上的无线网络热点）

ap_scan=1

# 简单的情形：WPA-PSk密码验证方式，PSK是ASCII密码短语，所有合法的加密方式都允许连接

network={

  ssid="simple"

  psk="very secret passphrase"

  # 优先级越高，就能越早匹配到。

  priority=5

}

To allow unprivileged users to control the connection using wpa_gui / wpa_cli, make sure GROUP=wheel and update_config=1.

也可以使用wpa_passphrase 命令添加无线热点

wpa_passphrase [ ssid ] [ passphrase ] >> /etc/wpa_supplicant/wpa_supplicant.conf

上面这条命令可以自动生成一段配置，我们将它输出添加到 wpa_supplicant 的默认配置文件里面。

wpa_cli

运行wpa_cli时可能会出现如下的错误：

Could not connect to wpa_supplicant - re-trying

这个错误可能是因为你的wpa_supplicant进程没有启动起来造成的。

wpa_cli

> scan

> scan_results

> add_network

0

> set_network 0 ssid "MYSSID"

> set_network 0 psk "passphrase"

> enable_network 0

> save_config

OK

dhcpcd interface

设置、获取IP

自动获取

dhcpcd wlan0

手动设置

ifconfig wlan0 192.168.1.11 broadcast 192.168.1.255 netmask 255.255.255.0

告知Gentoo RC系统网卡名字

cd /etc/init.d

ln -s net.lo net.wlan0

#start and stop it using the following commands:

/etc/init.d/net.eth0 start

/etc/init.d/net.eth0 stop

#开机启动

rc-update add wlan0 default

相关文章